User manual ICOM RS-RP2C

[. . . ] GATEWAY CONTROL SOFTWARE rs- rp2c Set Up Instructions IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the repeater. SAVE THIS INSTRUCTION MANUAL. This manual contains important safety and operating instructions for the RS-RP2C. TABLE OF CONTENTS IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i 1 PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The ISO image is the same format as the recorded in a CD. When this ISO image is recorded in CD as a file, OS cannot be installed with the CD. NOTE: See the instruction manual of the CD writing software about a detailed operation, the ISO image recording procedures, etc. 1 1 PREPARATION I Linux® OS installation Refer to the appropriate distributor's home page about the details of the OS installation. See the addresses listed below for your information. Any support from RedHat has already been finished, however, the update package is supplied from Fedora legacy Project. (*The following addresses may delete or change without notice. ) For your information · Fedora Core 2 http://fedoraproject. org/ http://fedora. redhat. com/ · RedHat® Linux® 9 - OS down load site http://ftp. redhat. com/pub/redhat/linux/9/en/iso/i386/ - ISO images necessary shrike-i386-disc1. iso, shrike-i386-disc2. iso, shrike-i386-disc3. iso - Installation description http://www. redhat. com/docs/manuals/linux/RHL-9-Manual · Fedora Legacy Project http://www. fedoralegacy. org/ I DNS name server installation Install the DNS name server if not installed. q Open "Add/Remove Applications" with the following mouse operation. e Click "" mark beside "Extra Packages" then click to apply check mark, ", " at "caching-nameserver. " · Click [× Close] after the setting. c Click x Select x Click to add ". " z Click z Click w Click "DNS name Server" to add a check mark, ", " and then click "Details. " c Click r Click [Update] to start the installation. Click to add ". " Click Click 2 SYSTEM SETUP I Gateway server connections D Connecting to the ID-RP1 system ID-RP1D (Zone repeater) Gateway server 2 to Internet Modem LAN card: eth0 LAN card: eth1 to [ 10B AS E-T ] Router to eth0 to eth1 Coupler D Connecting to the ID-RP2 system ID-RP2 (Zone repeater) Gateway server to Internet Modem LAN card: eth0 LAN card: eth1 Router to eth0 to eth1 to [10BASE-T] 3 2 SYSTEM SETUP I Router settings D IP address setting Set the specified IP addresses for both WAN and LAN as follows. IP address (WAN) : Enter the fixed global IP address that is specified from the ISP. IP address (LAN) : 10. 0. 0. 1 NOTE: The same IP address (for LAN; 10. 0. 0. 1) is used for all gateways. NEVER use other private IP address. D Port forwarding setting Set the following port number with protocol to transferring to the IP address "10. 0. 0. 2. " Port No. /Protocol 20005/TCP Usage IP server synchronization File location PORT_SYNC (/etc/dsipsvd. conf) GW_VCPORT (/etc/dsgwd. conf) GW_DTPORT (/etc/dsgwd. conf) 40000/UDP Voice transfer 40001/TCP Data transfer NOTE: IP filter must be set to allowing Internet remote access to local IP address "10. 0. 0. 2. " Otherwise the D-STAR gateway will not work due to the firewall. I Sever settings D LAN card settings q Open "Network Configuration" screen with the following mouse operation. x Select NOTE: The fixed value for both the IP address and subnet mask must be set to both eth0 and eth1. Otherwise the gateway server cannot communicate to another D-STAR gateway. e Select [Statically set IP address], then enter the specified IP address, subnet mask and default gateway (router side; eth0 setting only), as below. Click [OK], then close "Ethernet Device" screen. Displays the LAN card name that is selected in steps w. c Click eth0: 255. 0. 0. 0 eth1: 255. 255. 255. 0 eth0: 10. 0. 0. 2 eth1 172. 16. 0. 20 z Click Select w Select [eth0] or [eth1] to select router or repeater side respectively, then click [Edit]. · The "Ethernet Device" screen appears as right above. Click eth0: 10. 0. 0. 1 eth1: Blank Click r Click [DNS] tub in "Network Configuration" screen, then enter the address "127. 0. 0. 1" (fixed value) into "Primary DNS" column. For router For repeater Click Primary DNS: 127. 0. 0. 1 4 SYSTEM SETUP 2 D Named setting IMPORTANT!: Master the basis of BIND with a reference book of Linux, before starting the named setting. q Add local zone setting file (dstar. local. ) to "/etc/named. conf. " · e. g. ; /etc/named. conf v Click c Select x Select e Open "Service Configuration" screen with the following mouse operation. Add z Click r Click the check box beside "named, " then save the changed setting if no check mark, ", " is added. w Create database, /var/named/dstar. local. db, for local D-STAR as the following example. NOTE: A full-stop period must be applied into 2nd, 3rd and 10th lines. And set the separator as below at the end of the line. ;##DSTAR A RECORD · e. g. ; /var/named/dstar. local. db x Click c Click to save z Click to add check mark, ". " Full stop period Full stop period t Select "named" item, then click [Restart] to restart the named setting. x Click Full stop period z Select Separator For your information When "Fedora Core 2" is used, the database location is "/var/named/chroot/var/named/dstar. local. db. " 5 2 SYSTEM SETUP D DNS function verification q Start up "Terminal" with the following mouse operation. e When the correct router IP address "10. 0. 0. 1" is displayed in the answer section as below, the GW setup is succeeded. x Select Enter the command z Click c Click Router IP address w The local DNS operation can be verified by entering the following command. # dig router. dstar. local I Gateway control software D Installation q Insert the RS-RP2C CD into the drive. [. . . ] Enter the local IP address of the target server divided by full stop (. ). Enter the target HOST name that is used for DNS. Usable characters: A-Z, a-z, 0-9, _, /, [, ], + Enter the file name that is specified by the absolute path. Description 10 SYSTEM SETUP 2 D Local IP address reservation q Enter the following command in the Terminal-2. [. . . ]