User manual IDEAL 630

[. . . ] #61-633 #61-635 630 Series Technician Grade Multimeter 1 2 3 4 5 1. DO NOT UNDER ANY CIRCUMSTANCES EXCEED THESE RATINGS: - Voltage is not to exceed 1000 Volts. - Resistance, Capacitance, Logic and Continuity functions are not to be performed on circuits capable of delivering greater than 600 Volts. - Current measurements are not to be performed on circuits capable of delivering greater than 500 Volts 2. [. . . ] 7 REF (Reference) continued · Press the and buttons to move left and right through the reference value to select the appropriate digit to be changed. · The + and ­ buttons will increase or decrease the value of the blinking digit. · The actual measurement will be displayed in the upper right display while in the REF function. · Pressing the F4 button until the will save the reference value and exit the REF function. Setup · Pressing F1 while the indicates row F4 enters and exits the setup mode. · The parameters within the setup menu are: A. 1 bEEP ­ Turns the beeper on or off B. ­ Sets the time for auto power off (in minutes) C. 3 b. LitE ­ Sets the time for auto back light off (in minutes) D. 4 HAZ ­ Set hazard detect function on or off E. 5 L. FrEq ­ Set power line frequency to 50 or 60Hz F. 6 LoAd ­ Set the dBm load in the dBm mode G. 7 rESEt ­ Resets all setup parameters except power line frequency setting back to factory default settings · Press the and buttons to move left and right through the parameters of the setup menu. · The + and ­ buttons change the values of the selected setup parameter. · To exit the setup menu without saving changes to the menu parameters, press the blue button. · Turning the meter off does not affect changes to the setup menu. 8 DBm, dB · Press the F3 button while the indicates row M4 toggles between dBm and dB mode. · In dB mode, the measurement value is displayed in the upper right display, and the dB value is displayed in the main display. · In dBm mode, the dBm load is displayed in the upper right display. · Press and hold the F3 button for 2 seconds to exit dBm/dB mode. Send · Press the F4 button while the indicates row M4 to activate the data acquisition and send data through the optical RS232 connection. · The RS232 indicator appears in the display while data is being sent. [. . . ] Features LCD Backlight Adjustable Auto Backlight Off RS-232 Phototronic Serial Port RS-232 Cable DMM300 Software Holster and Stand Safety CE Mark 61-633 · · · Option Option · IEC, UL, CSA · 61-635 · · · · · · IEC, UL CSA · Physical Characteristics Dimensions: 200mm x 90mm x 42mm 212mm x 100mm x 55mm (w/holster) Weight (w/battery): 420g Weight (w/holster): 650g Enviornmental Characteristics Temperature Operating: 0 to +50°C Non-Operating (storage): -20 to +60°C Humidity (Operating): <80% Altitude (Operating): 2, 222m (7290 ft. ) Altitude (Non-Operating): 12, 300m (40354 ft. ) Vibration & Shock (Operating): MIL-T-28800E Type II Class 5 2. 66g RMS, 5 to 500 Hz, 3 axes, (10 min. each) Vibration & Shock 3. 48G RMS, 50 to 500 Hz, 3 (Non-Operating) axes, (10 min. each) Dust/Water Protection IP Rating: IP 64 23 Certifications & Compliances Safety: Designed to IEC 1010-1, UL3111 and CSA Specifications Input Rating: 1000VDC Category II 600VDC Category III 750VAC Category II 600VAC Category III Cat III: Distribution level mains, fixed installations Cat II: Local level mains, appliances, portable equipment Overvoltage Category: Cat I: Signal level, special equipment or parts of equipment, telecommunication, electronics Pollution Degree 2: Do not operate in environments where conductive pollutants may be present. C US Maintenance Warning To avoid electrical shock, remove test lead before opening the cover. Repairs or servicing not covered in this manual should only be performed by qualified personnel. 24 Battery Installation or Replacement: The #61-633 and #61-635 are powered by one 9 volt battery. [. . . ]