User manual IDEAL ND2365

[. . . ] #61-481 Symbols in this Manual This symbol indicates where cautionary or other information is found in the manual. Fuse Battery Refer to Figure 1 and to the following numbered steps to familiarize yourself with the meter's front panel controls and connectors. 480 Platinum Pro Series Commercial Contractor Grade Multimeter 1 7 Hz Hz 9 10 8 2 True RMS True RMS 4 3 5 6 2 1. Digital Display ­ The digital display has 4000 counts LCD readout with 82 segments analog bar graph, auto polarity, decimal point, " " AC, DC RANGE, H APO and unit annunciators. Rotary Switch ­ Select the Function and Range desired. [. . . ] Plug the black test lead into the COM port and the red test lead into the VH port. Set the rotary switch to the V position. Push the blue button until AC is shown on the display. Connect the meter in parallel with the load or circuit. 6 5 DC Volts Circuit Connection: True RMS AC Current Circuit Connection: Hz Hz True RMS True RMS Range 400mV 4V 40V 400V 1000V Resolution 100µV 1mV 10mV 100mV 1V Max Display Accuracy 400. 0 ±(0. 25% +5) 4. 000 ±(0. 4% +1) 40. 00 ±(0. 25% +1) 400. 0 1000 Range 40mA 400mA 10A Resolution 10µA 0. 1mA 10mA Max Display 40. 00 400. 0 10. 00 Accuracy ±(2. 0% +5) ±(2. 5% +5) Voltage Burden 200mV max 2Vmax 2V max Input Impedance: 10M (over 1000M in 400mV range) To Measure DC Voltage: 1. Plug the black test lead into the COM port and the red test lead into the VHz port. Set the rotary switch to the V position. Push the blue button until DC is shown on the display. Connect the meter in parallel with the load or circuit. Measure DC Voltage. AC Conversion Type: AC conversions are ac-coupled, true rms responding, calibrated to the rms value Sine wave input. Overload Protection: 1A (500V) fast blow fuse for mA input 16A (500V) fast blow fuse for A input Crest Factor: +1. 5% additional error for C. F. from 1. 4 to 3 +3. 0% additional error for C. F. from 3 to 4 To Measure True RMS AC Current: 1. Plug the black test lead into the COM port and the red test lead into the mA or A port. Set the rotary switch to the mA or A position. Push the blue button until AC is shown on the display. Connect the meter in series with the load or circuit. 8 7 DC Current Circuit Connection: Frequency/RPM Circuit Connection: Hz Hz True RMS True RMS Range 40mA 400mA 10A Resolution 10µA 0. 1mA 10mA Max Accuracy Voltage Display Burden 40. 00 ±(0. 6% +2) 200mVmax 400. 0 ±(0. 7% +2) 2Vmax 10. 00 ±(1. 0% +2) 2V max Range 4. 0KHz/40KRPM 40KHz/400KRPM 400KHz/4MRPM 4MHz/40MRPM 40MHz/400MRPM Resolution 1Hz/300RPM 10Hz/300RPM 100Hz/3KRPM 1KHz/30KRPM 10KHz/300KRPM Sensitivity 100mV rms* Accuracy Frequency: 0. 01% ±1 digit RPM: 0. 01% ±10 digits Overload Protection: 1A (500V) fast blow fuse for A input 16A (500V) fast blow fuse for A input To Measure DC Current: 1. Plug the black test lead into the COM port and the red test lead into the mA or A port. Set the rotary switch to the mA or A position. Push the blue button until DC is shown on the display. Connect the meter in series with the load or circuit. [. . . ] Normally the forward voltage drop of a good silicone diode is shown between 400V and 90V. If the diode under test is defective, "000" (short circuit) or "OL" (non-conductive) is displayed. 15 Range 4nF 40nF 400nF 4µF 40µF 400µF 4mF 40mF Resolution 1pF 10pF 100pF 1nF 10nF 100nF 1µF 10µF Max Display 4. 000 40. 00 400. 0 4. 000 40. 00 400. 0 4. 000 40. 00 Accuracy ±(3. % reading +10 digits) ±(2% reading +8 digits) ±(5% reading +20 digits) Overload Protection: 600V rms To Measure Capacitance: 1. Plug the black test lead into the COM port and the red test lead into the VHz port. [. . . ]