User manual IIYAMA H511S

[. . . ] USER MANUAL ENGLISH DEUTSCH FRANCAIS NEDERLANDS Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. ITALIANO ESPAÑOL Congratulations! The display you have just purchased carries the TCO'03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. [. . . ] Hold the stand so that the monitor does not topple when you change the monitor's angle. you are able to adjust the monitor's height up to 110mm, angle up to 35degrees right and left, 35 degrees upward, 5 degrees downward. NOTE Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the angle. 110mm PANEL ROTATION : ProLite H511S A Ajust the monitor's height to the maximum. NOTE Attempting to rotate without fully extending upward may cause damage to stand. Please use attached Pivot® software for rotating the image on the screen. C Ajust the monitor's angle to your preference. BEFORE YOU OPERATE THE MONITOR 11 ENGLISH OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 31. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 22 for SCREEN ADJUSTMENTS. ( Press the Menu Button to start the On Screen Display feature. There are additional Menu pages which can be switched by using the +/­ Buttons. Displayed while Economy Mode is active. Displayed while Mute is active. ENGLISH 1 LOCK Menu:1 Page no. Adjustment icon Current horizontal frequency, vertical refresh rate and resolution 1600 × 1200 H:75. 0KHz V:60. 0Hz B Select the Menu page which contains the adjustment icon relating to the adjustment you want to make. Then, use the +/­ Buttons to highlight the desired adjustment icon. Press the Menu Button again. C Use the +/­ Buttons to make the appropriate adjustment or setting. For example, to correct for vertical position, select Menu page number 1 and then press the Menu Button. Then, select (V-Position) by using the +/­ Buttons. Menu:1 1600 × 1200 H:75. 0KHz V:60. 0Hz An adjustment scale appears after you press the Menu Button. Use the +/­ Buttons to change the vertical position settings. The vertical position of the overall display should be changing accordingly while you are doing this. V-Position The bar shows the progress of the adjustment being made. ­ + 50 NOTE When button operations are aborted during adjustment, On-Screen Display disappears when the time set for the OSD Off Timer has passed. The Exit button can be used to exit OSD window immediately. Adjustments for Clock, Phase and Position are saved for each signal timing. Except for these adjustments, all other adjustments have only one setting which applies to all signal timings. 12 OPERATING THE MONITOR ADJUSTMENT MENU CONTENTS Analog Input Menu : 1 (Analog) Menu:1 1600 × 1200 H:75. 0KHz V:60. 0Hz Adjustment Item Brightness *1 Direct Problem / Option Too dark Too bright Too dull Too intense Button to Press Contrast Direct Clock * 2 To correct flickering text or lines Phase * 2 To correct flickering text or lines Too low Too high Too far to the left Too far to the right Highlight "Menu :1" again. V-Position H-Position Return to Menu *1 Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too * 2 bright. See page 22 for SCREEN ADJUSTMENTS. Direct You can skip the Menu pages and display an adjustment scale directly by using the following button operations. Brightness: Contrast: Press the Brightness Button when the Menu is not displayed. [. . . ] Turn off the Power Switch whenever the monitor is not in use, during the night and weekends, to avoid unnecessary power consumption. It is possible that the video signal from the computer may be on while the H or V sync signal is missing. In this instance, the POWER MANAGEMENT feature may not work properly. OPERATING THE MONITOR 25 ENGLISH Power Management Mode When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. [. . . ]