User manual IIYAMA PROLITE B2409

[. . . ] USER MANUAL ENGLISH DEUTSCH FRANCAIS NEDERLANDS Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. ENGLISH Congratulations! The display you have just purchased carries the TCO'03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. [. . . ] Make sure you tighten the finger screws at each end of the signal cable. ENGLISH [Example of Connection] <Back> Power Cable (Accessory) Audio Cable (Accessory) D-Sub Signal Cable (Accessory) DVI-D Signal Cable (Accessory) HDMI Cable (Not included) Computer [ Collect Cables ] A Put the cables through the cable holder. B Collect cables at the back of the stand. 9 BEFORE YOU OPERATE THE MONITOR CONNECTING YOUR MONITOR : ProLite E2209HDS A Ensure that both the computer and the monitor are switched off. B Connect the computer to the monitor with the signal cable. C Connect the monitor to the audio equipment with the Audio Cable for computer when using the audio features. D Connect the Power Cable to the monitor first and then to the power supply. E Power of the monitor and the computer is turned on. NOTE The signal cables used for connecting the computer and monitor may vary with the type of computer used. An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office. For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama office for a suitable adaptor. Make sure you tighten the finger screws at each end of the signal cable. [Example of Connection] <Back> Power Cable (Accessory) Audio Cable (Accessory) D-Sub Signal Cable (Accessory) DVI-D Signal Cable (Accessory) HDMI Cable (Not included) Computer BEFORE YOU OPERATE THE MONITOR 10 ENGLISH COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 29: COMPLIANT TIMING. Windows 95/98/2000/Me/XP/Vista Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied. For installation on Windows 95/98/2000/Me/XP: The monitor Information File for iiyama monitors ENGLISH may be necessary for your computer and obtained via the Internet, using the address: http://www. iiyama. com NOTE For additional information on how to download the driver for your touch screen monitor, please access the internet site noted above. Monitor Drivers are not required in most cases for Macintosh or Unix operating systems. For further information, please contact your computer dealer first for advice. 11 BEFORE YOU OPERATE THE MONITOR ADJUSTING THE HEIGHT AND THE VIEWING ANGLE : ProLite B2409HDS For optimal viewing it is recommended to position yourself directly opposite to the full face of the monitor, then adjust the monitor's height and angle to your own preference. Hold the panel so that the monitor does not topple when you change the monitor's height or angle. degrees upward. NOTE Do not touch the LCD screen when you change the height or the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the height or the angle. ADJUSTING THE VIEWING ANGLE : ProLite E2209HDS For optimal viewing it is recommended to look at the full face of the monitor. Hold the stand so that the monitor does not topple when you change the monitor's angle. [. . . ] Turn off the Power Switch whenever the monitor is not in use, during the night and weekends, to avoid unnecessary power consumption. It is possible that the video signal from the computer may be on while the H or V sync signal is missing. In this instance, the POWER MANAGEMENT feature may not work properly. 23 OPERATING THE MONITOR TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. [. . . ]