User manual INDESIT K3G21S-IR

[. . . ] Operating Instructions COOKER GB GB English, 1 Contents Installation, 2-6 Positioning and levelling Electrical connections Gas connection Adapting to different types of gas Technical data Table of burner and nozzle specifications Description of the appliance, 7 Overall view Control panel Start-up and use, 8-10 K3G2/G K3G21/G K3G21S/IR K3G2S/G Using the hob Using the oven Analogue timer Oven cooking advice table Precautions and tips, 11 General safety Disposal Respecting and conserving the environment Maintenance and care, 12 Switching the appliance off Cleaning the appliance Gas tap maintenance Replacing the oven light bulb Assistance Installation GB Before operating your new appliance please read this instruction booklet carefully. It contains important information concerning the safe installation and operation of the appliance. Please keep these operating instructions for future reference. Make sure that the instructions are kept with the appliance if it is sold, given away or moved. [. . . ] Remove the oven burner after loosening screw V (see figure). V GB Adapting the oven Replacing the oven burner nozzle: 1. Slide out the protection panel A (see diagram). Unscrew the grill burner nozzle using a special nozzle socket spanner (see figure) or preferably with a 7 mm socket spanner, and replace it with a new nozzle that is suited to the new type of gas (see Burner I and nozzle specifications table). Be careful of the spark plug wires and the thermocouple tubes. The oven and grill burners do not require primary air adjustment. After adjusting the appliance so it may be used with a different type of gas, replace the old rating label with a new one that corresponds to the new type of gas (these labels are available from Authorised Technical Assistance Centres). To light one of the burners on the hob: 1. Bring a flame or gas lighter close to the burner. Press the BURNER knob and turn it in an anticlockwise direction so that it is pointing to the maximum flame setting -. Adjust the intensity of the flame to the desired level by turning the BURNER knob in an anticlockwise direction. This may be the minimum setting +, the maximum setting - or any position in between the two. If the appliance is fitted with an electronic lighting device* (see figure), press the ignition button, marked with the symbol , then hold the BURNER knob down and turn it in an anticlockwise direction, towards the maximum flame setting, until the burner is lit. Several models are equipped with an ignition device which is built into the knob; in this case the electronic ignition device* is present (see figure) but the ignition button is not. Simply press the BURNER knob and turn it in an anticlockwise direction so that it is pointing to the maximum flame setting, until the burner is lit. The burner may be extinguished when the knob is released. If this occurs, repeat the operation, holding the knob down for a longer period of time. If the flame is accidentally extinguished, switch off the burner and wait for at least 1 minute before attempting to relight it. If the appliance is equipped with a flame failure safety device*, press and hold the BURNER knob for approximately 2-3 seconds to keep the flame alight and to activate the device. To switch the burner off, turn the knob until it reaches the stop position . HOB GAS BURNER SAFETY DEVICE Practical advice on using the burners . or the burners to work in the most efficient way possible and to save on the amount of gas consumed, it is recommended that only pans that have a lid and a flat base are used. They should also be suited to the size of the burner. Burner Fast (R) Semi Fast (S) Auxiliary (A) ø Cookware diameter (cm) 24 - 26 16 - 20 10 - 14 To identify the type of burner, please refer to the diagrams contained in the Burner and nozzle specifications. Using the oven The first time you use your appliance, heat the empty oven with its door closed at its maximum temperature for at least half an hour. Ensure that the room is well ventilated before switching the oven off and opening the oven door. The appliance may emit a slightly unpleasant odour caused by protective substances used during the manufacturing process burning away. [. . . ] If the seals are damaged, please contact your nearest Authorised After-sales Service Centre. We recommend that the oven is not used until the seals have been replaced. Cleaning the appliance Do not use abrasive or corrosive detergents such as stain removers, anti-rust products, powder detergents or sponges with abrasive surfaces: these may scratch the surface beyond repair. Never use steam cleaners or pressure cleaners on the appliance. It is usually sufficient simply to wash the hob using a damp sponge and dry it with absorbent kitchen roll. [. . . ]