User manual INDESIT VRM 640 C

[. . . ] 9 USING THE HOB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 CLEANING AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 POSITIONING IN THE COUNTER TOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 ELECTRICAL CONNECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please help by disposing of the packaging correctly. You can obtain the addresses of collection, recycling and disposal centres from your retailer or from the competent local organisations. Do not discard the packaging or any part of it, or leave it unattended. It can constitute a suffocation hazard for children, especially the plastic bags. Your old appliance also needs to be disposed of correctly. Important: hand over your appliance to the local agency authorised for the collection of household appliances no longer in use. Correct disposal enables intelligent recovery of valuable materials. Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use, to ensure that children cannot accidentally become trapped inside during play. It is also necessary to cut the connecting cable to the power grid, removing it along with the plug. 8 Instructions for the user 4. DESCRIPTION OF CONTROLS 4. 1 Control zone All the hob controls are grouped together on the front panel. CONTROL ZONE 4-burner hob 5-burner hob KNOB DESCRIPTION To light the flame, press the knob and turn it anticlockwise to between the maximum minimum flame symbol and the . How to use: pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or a microfibre cloth. 6. 1. 2 Food stains or residues Do not use metallic sponges or sharp scrapers: they will damage the surface. Use ordinary non-abrasive products, together with anti-scratch sponges and wooden or plastic utensils if necessary. Rinse thoroughly and dry with a soft cloth or microfibre cloth. 6. 2 Cleaning the components 6. 2. 1 Knobs The knobs should be cleaned with lukewarm water and washing up liquid. For easier cleaning they can be removed by pulling them upwards. Do not use aggressive products containing alcohol or products for cleaning steel and glass when cleaning the knobs, as these products could cause permanent damage. 14 Instructions for the user 6. 2. 2 Pan stands Remove the pan stands and clean them with lukewarm water and non-abrasive detergent, making sure to remove any encrustations. After having fastened the hob to the unit (See "7. 3 Fixing using brackets"), carefully trim the surplus away from edge C beyond the seal. The dimensions given in the following drawing refer from the hole to the inside of the seal. 17 Instructions for the installer 7. 3 Fixing using brackets The figure to the side shows the exact holes to be used to correctly attach the hob to the counter top with brackets. Fix the hob to the unit using the appropriate brackets supplied. To secure the hob correctly to the counter top, tighten the brackets A in the appropriate holes on the sides of the casing. Take care while securing with the brackets; if tightened too much the glass may be strained causing it to crack. 18 Instructions for the installer 8. ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations. [. . . ] Make sure that the feed pressure complies with the values indicated in the table at point "10. ADAPTATION TO DIFFERENT TYPES OF GAS". 9. 2 Room ventilation The room containing the appliance should be permanently ventilated in accordance with the standards in force. The room where the appliance is installed must have enough air flow needed for the regular combustion of gas and the necessary air change in the room itself. The air vents, protected by grills, must be the right size to comply with current regulations and positioned so that no part of them is obstructed, not even partially. [. . . ]