User manual INFINITY C205

[. . . ] See Page 3. Couch PLACEMENT Stereo Before deciding where to place your speakers, survey your room and think about placement, keeping the following points in mind, using Figure 1 as a guide: · For best results, place the speakers 6'­ 8' apart. · Position each speaker so that the tweeter is approximately at ear level. · Generally, bass output will increase as the speaker is moved closer to a wall or corner. [. . . ] If a wall stud is not available, use an appropriate anchor. Place the speaker on the wall by aligning the keyholes on the back of the speaker to the screwheads on the wall. Once positioned properly, the speaker should slide down slightly and become secure. Carefully slide the cleats on the rear of the speakers over the tabs of the wall bracket. INSTALLING SPIKED FEET C336 Four metal spikes are supplied for use when using the outboard feet and the speaker is to be placed on a carpeted surface to decouple the speaker from the floor and prevent unwanted damping. To insert the spikes, gently lay the speaker on its back (not its front or side) on a soft, nonabrasive surface, unscrew the four rubber-tipped feet and store in a safe place. Each spike then screws into the threaded insert. Make sure all four spikes are screwed in completely for stability. NEVER drag the speaker to move it, as this will damage the spikes, the feet, the wood cabinet itself, and/or the floor. Always lift the speaker and carry it to its new location. Top view INFINITY CLASSIA 3 WIRING THE SYSTEM IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a minimum #16-gauge speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i. e. , +). NOTE: If desired, consult your local Infinity dealer about speaker wire and connection options. The speakers have coded terminals that accept a variety of wire connectors. The most common connection is shown in Figure 5. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown in Figure 6. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier, receiver and television to confirm connection procedures. IMPORTANT: Do not reverse polarities (i. e. , + to ­, or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. BI-WIRING C336 The outer connection panel and internal dividing network of the C336 is designed so that separate sets of speaker cables can be attached to the lowfrequency transducer and midrange/high-frequency transducer portions of this dividing network. This is called bi-wiring. Bi-wiring can provide several sonic advantages and considerably more flexibility in power amplifier selection. Figure 7. Single-Stereo Amplifier Figure 5. This example shows how to connect bare wires to the terminals. Figure 8. Dual-Stereo Amplifier Figure 9. Figure 6. [. . . ] When needed, use a soft cloth to remove any fingerprints or dust. NOTE: Do not use any cleaning products or polishes on the cabinet or grille. In the event that your Infinity speaker needs service, contact your Infinity dealer or distributor, or visit www. infinitysystems. com for the location of the nearest service center. INFINITY CLASSIA 5 SPECIFICATIONS C205 Frequency Ranges: Recommended Amplifier Power Range: Sensitivity (2. 83V @ 1 meter): Nominal Impedance: Crossover Frequencies: Low-Frequency Driver(s): Mid-Frequency Driver: High-Frequency Driver: Dimensions (H x W x D): Weight: 60Hz ­ 30kHz (­3dB) 55Hz ­ 40kHz (­6dB) C336 40Hz ­ 30kHz (­3dB) 35Hz ­ 40kHz (­6dB) CC225 55Hz ­ 30kHz (­3dB) 50Hz ­ 40kHz (­6dB) 10 ­ 125 Watts 88dB 8 Ohms 2. 0kHz; 24dB/octave 5-1/4" (133mm) CMMD, ® magnetically shielded N/A 10 ­ 250 Watts 91dB 8 Ohms 500Hz, 2. 8kHz; 24dB/octave Triple 6-1/2" (165mm) CMMD, ® magnetically shielded 4" (100mm) CMMD, magnetically shielded 1" (25mm) CMMD, magnetically shielded 48-3/4" x 8-1/2" x 10-1/2" (1238mm x 216mm x 267mm) 56. 1 lb (25. 4kg) 10 ­ 150 Watts 90dB 8 Ohms 2. 0kHz; 24dB/octave Dual 5-1/4" (133mm) CMMD, ® magnetically shielded N/A 1" (25mm) CMMD, magnetically shielded 15-1/8" x 7-1/2" x 9-1/4" (384mm x 190mm x 235mm) 10. 8 lb (4. 9kg) 1" (25mm) CMMD, magnetically shielded 6-7/8" x 31-3/4" x 5" (175mm x 806mm x 127mm) 16 lb (7. 3kg) Features, specifications and appearance are subject to change without notice. Declaration of Conformity We, Harman Consumer Group, Inc. [. . . ]