User manual INFOCUS LITEPROLS Reference Guide

[. . . ] Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. InFocus, LiteShow, ASK Proxima, and LP are trademarks or registered trademarks of InFocus Corporation. User's Guide Travel Restrictions You must keep this User's Guide with your LiteShow adapter at all times when traveling in countries other than the United States of America. FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] The WEP key is either 40bit (10 characters long) or 104bit (26 characters long). If you are using a Macintosh, you must use Airport Admin to convert a Mac password into a valid WEP key. Note that there will be a period of time between when the WEP key is sent to be authenticated and when you are able to project. Authentication Type: Choose a method of verifying the WEP key between the wireless network interface card (NIC) and the access point (AP), Shared Key or Open System. · Shared Key: With shared key authentication, the AP sends the client device (LiteShow) a text packet that the client must then encrypt with the correct WEP key and return to the AP. This is the default setting; only try Open System if this does not work. Open System: Open system authentication involves the LiteShow supplying the correct Service Set Identifier (SSID) to the AP. No encryption takes place. · InFocus LiteShow User's Guide 23 Troubleshooting and Frequently Asked Questions Troubleshooting No LiteShow adapters appear in the list of LiteShow Manager. Try the following: · · · · · · · · · Make sure that the LiteShow-enabled projector is in range with your computer and that the projector is powered on. Make sure your computer has a valid IP address. Make sure that your computer's wireless adapter is installed, plugged in, and enabled. Network Switching One of the features of LiteShow is the ability to switch from one network to another and to find available projectors on other networks via the LiteShow Manager's Scan button. When you look at the LiteShow Manager and see two LiteShow-enabled projectors, one is, for example, on the "LiteShow" WLAN (or network) and the other is, for example, on the "myCorporateNetwork" WLAN. You start projecting through the projector on the "LiteShow" WLAN. With a wireless 802. 11b driver that supports network switching, you can stop projecting through the "LiteShow" WLAN and switch to the projector on the "myCorporateNetwork" WLAN. This is known as the Advanced Feature set. With basic network switching the Scan button is not operational. This is known as the Basic Feature set. However, when the Advanced Feature set is not supported, you have two options: · · Update your wireless network driver or Set up network profiles InFocus LiteShow User's Guide Update a Wireless Driver 27 Contact your wireless hardware vendor's technical support for 802. 11b driver updates. Most vendors now support WLAN configuration options that provide for advanced network switching features. The Advanced Feature set in the LiteShow Manager is referencing this WLAN Network Device Interface Specification - Object Identifier (NDIS-OID) application, or advanced network switching, interface that allows PC applications to configure network properties. This allows LiteShow Manager to automatically switch networks and identify LiteShow Adapters on detected WLAN's. In the event that your wireless PC adapter vendor does not support advanced network switching, refer to the www. infocus. com/service/liteshow website for known compatible 802. 11b wireless cards. [. . . ] The sales receipt or invoice, showing the date of purchase of the Product is the proof of the date of purchase. To Obtain Warranty Service During the Limited Warranty period, to exercise this Limited Warranty, the purchaser must first contact 1) InFocus, 2) a service facility authorized by InFocus or 3) the place of original purchase. InFocus Customer Service ­ 1-503-685-8888 or visit www. infocus. com/service For Warranty service, the purchaser will be advised to return or deliver the defective Product freight and all fees pre- LiteShow User's Guide 45 paid, to an InFocus Service Center or to a service facility authorized by InFocus. When returning Product to InFocus, a Service Request Number (SR #) is required and must be clearly displayed on the outside of the shipping carton or a similar package affording an equal degree of protection. [. . . ]