User manual INFOCUS LITESHOW

[. . . ] LiteShow® WIRELESS FREEDOM FOR YOUR PROJECTOR. USER'S GUIDE Declaration of Conformity Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USA European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands We declare under our sole responsibility that the LiteShow wireless projection adapter conforms to the following directives and norms: EMC Directive 89/336/EEC, Amended by 93/68/EEC EMC: EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC Safety: EN 60950: 2000 The Agency/Regulatory Approval for the computer's wireless adapter is solely the responsibility of the adapter manufacturer - not InFocus Corporation. July, 2004 Trademarks Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc. [. . . ] Make sure your computer has a valid IP address. Make sure that your computer's wireless adapter is installed, plugged in, and enabled. Make sure that your computer's wireless adapter antenna is switched on or extended. Make sure that your computer's wireless adapter is configured to match the settings that display on the LiteShow splash screen. Refer to information on Infrastructure and Ad-Hoc modes on page 20. For more detailed information, visit the InFocus website at www. infocus. com/service/liteshow. Physically move the computer so that it is closer to the LiteShow adapter. Check to see that there are no interfering 802. 11b or 2. 4 GHz devices, such as Bluetooth wireless devices or microwave ovens in use, in the area of the computer and LiteShow adapter. Cordless phones and microwave ovens may also cause performance problems. Move the slidebar in the Preferences box to Better Performance. Performance is poor; projection takes a long time. Try the following: · 24 Resetting your LiteShow To reset your LiteShow to the original factory settings, do the following: InFocus LiteShow User's Guide 1 Remove the LiteShow module from the projector. Remove the LiteShow module 2 Grasp the module in both hands. Press firmly on the ribbed portion of the clear plastic top to disengage the locking tab. The tab is located on the back of the module. Then pull the top off of the module. Remove the top Remove the card 3 Pull the card out of the slot. Make sure to pull it straight out so you do not bend the connecting pins inside the module. InFocus LiteShow User's Guide 25 4 Replace the LiteShow on the projector (with the card still removed from the slot). A status dialog appears and provides a 30-second countdown for the reset. After several more seconds, the splash screen shows "Restored". The Splash Screen fields are updated with the preset values. The restore operation is complete when the following message appears on the projection screen "Factory Settings Restored". To cancel the reset, simply remove the LiteShow from the projector before the 30-second countdown expires. 5 Remove the LiteShow module from the projector. Replace the card by aligning it so that the colored label faces the back of the module and carefully inserting the card into the slot and pressing it into place. Replace the cap, then replace the LiteShow on the projector. 26 InFocus LiteShow User's Guide Frequently Asked Questions The following are questions that you may have about the LiteShow system and its individual parts. [. . . ] InFocus or the service facility authorized by InFocus will return the repaired/replaced Product freight prepaid to the purchaser. Products returned for Warranty service must be accompanied by a written letter that: (i) explains the problem; (ii) provides proof of date of purchase; (iii) provides the dealer's name; and (iv) provides the model and serial number of the Product. Upon request of InFocus Corporation or an authorized repair center for InFocus, proof of legal import must accompany the warranty repair Product, otherwise the Product must be returned to the place of original purchase, to the manufacturer (Purchaser must bear all tax, duty and freight), or the Purchaser must bear charges for the warranty repair. No repair or replacement of Product or part thereof shall extend the Limited Warranty period as to the entire Product. [. . . ]