User manual INFOCUS LP1200 Reference Guide

[. . . ] USER'S GUIDE 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH APPENDIX CAUTION ENGLISH RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified shielded power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception. [. . . ] PinP allows you to view different sources at the same time. The sub image will become a still picture. Press the PinP button on the remote control. · Pressing the PinP button repeatedly will select on and off. Select the desired external input source of the sub image by using the RGB, VIDEO or CARD button. · You can change the frame position and the frame size by using the on-screen menu. Expand By pressing the EXPAND button on the remote control, you can view the detailed image of the picture. Press the MENU button once to display the onscreen menu. Press the or buttons on the control panel (or $ or % buttons on the remote control) to select PinP/EXPAND. Press the ª or º buttons on the control panel (or { or } buttons on the remote control). Press the $ or % buttons on the remote control) to select ZOOM MODE, POSITION or SIZE. Press the ª or º buttons on the control panel (or { or } buttons on the remote control) to set the ZOOM MODE, POSITION or SIZE. To recapture the picture of sub screen 3 Press the ­ or + button. · By each press of the button will recapture the picture of sub screen. To switch Main image and sub image 4 Press the or buttons on the control panel (or $ or % buttons on the remote control). To switch still picture and playback picture between Main image and Sub image 5 Press the ª or º buttons on the control panel (or { or } buttons on the remote control) . Press the PinP button on the remote control. · In PinP mode, the sub image will become still pictures. When the main image is set to PC1 or PC2, the sub image will become moving pictures. · In PinP mode, the sound of the moving pictures will be heard. If this is the case, select the image again by pressing the `-' button. · In PinP mode you cannot adjust the zoom/focus. · Ajusting contrast, brightness, tint or color isn't available in PinP mode. · To use different PC card (PC card 1, PC card 2) on both Main image and Sub image is not available. [. . . ] " _r1 _r2 _v1 _v2 _c1 _c2 HEX 21h 22h 5Fh 5Fh 5Fh 5Fh 5Fh 5Fh 72h 72h 76h 76h 63h 63h 31h 32h 31h 32h 31h 32h [Example] Set the input signal to RGB1 (' 'is for ASCII code) Sending commands from the PC etc. 30 30 5F 72 31 OD '0' '0' '_' 'r' '1' ' ' 30 30 5F 72 31 OD '0' '0' '_' 'r' '1' ' ' Status code from projector Command for setting the input signal to RGB 1 Command received (Command echo back) Meaning 5) PCGC commands The remote control operation can be done by PCGC command codes. Button's name on remote POWER + VOLUME ­ VOLUME EXPAND PinP { } $ % MENU ENTER/STILL FOCUS/ZOOM AUTO PLAY RELEASE AUTO POSITION ASCII r3c r06 r07 r02 r04 r53 r2b r4f r59 r54 r10 r0f r32 r22 r09 HEX 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 33h 30h 30h 30h 30h 35h 32h 34h 35h 35h 31h 30h 33h 32h 30h 63h 36h 37h 32h 34h 33h 62h 66h 39h 34h 30h 66h 32h 32h 39h [Example] Display MENU selection bar. (' 'is for ASCII code) Sending commands from the PC etc. 30 30 72 35 34 OD '0' '0' 'r' '5' '4' ' ' 30 30 72 35 34 OD '0' '0' 'r' '5' '4' ' ' Command received (Command echo back) Status code from projector Command as same as MENU button Meaning APPENDIX Control this projector by using a personal computer (Continue) 6) Warning commands Read the recent warning data and the past warning data. [. . . ]