User manual INSINKERATOR ISE HOT WATER

[. . . ] Instant Hot Water Dispenser Owner's Manual Installation, Care & Use Instalacion, Cuidado & Uso Installation, Sion & Utilisation ® We are delighted that you have chosen the InSinkErator® Instant Hot Water Dispenser to be a part of your home. This unique appliance will save you time and effort in the kitchen, and you'll enjoy discovering new uses for it each day. That's exactly why millions of people are now using an InSinkErator Instant Hot Water Dispenser. We are confident that by following our step-by-step instructions, you'll soon be enjoying the convenience of instant hot water. WHAT YOU SHOULD KNOW BEFORE YOU BEGIN I For your satisfaction and safety, read all instructions, cautions, warnings and dangers before installing or using this instant hot water dispenser. [. . . ] Install head and bracket so that connections require no stretching, kinking or pinching of tubing. B from water supply line to dispenser I Determine length of tubing required, I Insert a white 3/8" tube into inlet I Insert the other white 3/8" tube Wing into Nut outlet side of filter head until it stops. Press in again to ensure a secure fit. then cut to length making sure the cut is perpendicular and burr-free. side of filter head until it stops. Press in again to ensure a secure fit. Plug Fiber Washer Property Damage: Tube runs need to form to the cabinet's contours to allow storage space with no sharp bends. Tubes need clean, perpendicular, burr-free cuts to ensure a true fit. Plug Plug Fiber Washer C GN1100/GN H-Wave/H-View Plug Plug H990/H770 HC1100/HC HC-Wave/HC-View I Insert the copper tube(s) from the I Connect the white 3/8" tube Fiber from Washer Fiber Washer Wing Nut Wing Nut FiberFiber Washer Washer dispenser into the 3/8" to 1/4" WingWing fitting. Nut quick-connectNut Plug From filter or water supply line Plug From filter or water supply line Property Damage: Do not extend the copper lines farther than the 16" provided. the right outlet on the filter Wing Nut head into the quick-connect fitting until it stops. Fiber Wing Nut Washer To remove tube(s) or plug from quick-connector, depress the release ring and gently pull away. D Discharge tube From water supply line To faucet I To redirect filter replacement water discharge, place 6" clear tube over vent hole on the left side of filter head. It is normal for approximately 2 oz. of water to discharge when filter is removed. 13 Insert 5A FINAL WATER CONNECTION Brass Nut Brass Nut Ferrule Ferrule Brass Insert Brass Nut Ferrule Brass Nut nsert Ferrule Property Damage:Nut remaining tube Brass Join to cold water supply only. Ferrule Brass Insert HC1100 / GN1100 / HC / HC-Wave / HC-View I At the end of the white 3/8" tube from the filter or quick-connector, slide the supplied brass nut and ferrule over the tube and then push in the brass tube insert. I Install a compression fitting, T-fitting or saddle valve (not included) onto the cold water supply line. I Insert the white 3/8" tube into the 3/8" Brass Nut compression fitting and tighten. Ferrule A ule Brass Insert Brass Nut Ferrule GN / H990 / H770 / H-Wave / H-View I Install a compression fitting, T-fitting or saddle valve (not included) onto the cold water supply line. I At the end of the copper 1/4" tube, Property Damage: Join remaining tube to cold water supply only. Nut I Insert the copper tube into the 1/4" compression fitting and tighten. slide the fitting's brass nut and ferrule over the tube. 6A Ferrule Brass Insert FILL TANK & THEN CONNECT POWER Ferrule Brass Nut I Turn on the cold water supply. I Depress or twist the dispenser's HOT handle and hold it until water flows from the spout. I Run the water for at least 2 minutes to Scalding Hazard: The faucet dispenses water up to 210ºF, which can instantly cause scalds or burns. Use care when operating this appliance. flush lines (both the hot and cold handles independently if applicable). B I Check all connections to ensure they are I Plug in instant hot water tank. Allow 12-15 minutes for water to reach target temperature. tight and that there are no leaks. Property Damage: A standard grounded outlet within 30" of the dispenser is required under the sink. Do not use an extension cord set with the dispenser. Gurgling or hissing is normal during the initial heating cycle. 14 Electric Shock Hazard: Using an ungrounded or improperly connected appliance can result in serious injury or death from electrical shock. This instant hot water dispenser is equipped with a cord that has a grounding conductor and a grounding pin. The plug must be connected to an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided with the appliance ­ if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Check with a qualified electrician or serviceman if you are in doubt as to whether the instant hot water dispenser is properly grounded. Personal Injury: This tank is a non-pressurized tank. DO NOT close vent tube or connect other type dispensers or valves to the tank. Use only the InSinkErator dispenser faucet supplied. Contact an authorized InSinkErator Service agent for repairs or replacement components. Fire Hazard: To minimize possibility of fire, DO NOT store flammable items such as rags, paper or aerosol cans near the tank. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. [. . . ] I To avoid water damage from leakage, replace all cut, loose or split tubing. I A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage. 16 Please read Troubleshooting Guide and/or visit www. insinkerator. com before calling AnswerLineTM TROUBLESHOOTING PROBLEM Water and steam spits forcefully from spout without turning on the dispenser faucet. POSSIBLE CAUSE · Unit is boiling. May be normal during initial setup. WHAT TO DO · Depress faucet lever to release some water from the tank. · Adjust water temperature using dial on tank front. [. . . ]