User manual INTEL D865PERL

[. . . ] Intel® Desktop Board D865PERL Product Guide Order Number: C24490-003 Revision History Revision -001 -002 -003 Revision History First release of the Intel® Desktop Board D865PERL Product Guide. Second release of the Intel Desktop Board D865PERL Product Guide. Third release of the Intel Desktop Board D865PERL Product Guide Date March 2003 April 2003 May 2003 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ] Observe the precautions in "Before You Begin" on page 27. Attach the cable end with the connector to the front panel USB 2. 0 header on the desktop board. Secure the cable's metal bracket to the chassis back panel with a screw. OM15480 Figure 14. Connecting a Rear Panel USB 2. 0 Adapter Table 11. Pin 1 3 5 7 9 USB 2. 0 Header Signal Names (J9F1 and J9H1) USB Port A Signal name Power DD+ Ground Key Pin 2 4 6 8 10 Power DD+ Ground No connect USB Port B Signal name Note: USB ports may be assigned as needed. 52 Installing and Replacing Desktop Board Components Connecting the Front Panel Header Before connecting the front panel header, observe the precautions in "Before You Begin" on page 27. Figure 13-D on page 50 shows the location of the front panel header. Table 12 shows the pin assignments for the front panel header. Table 12. Pin Signal 1 3 HD_PWR HDA# Front Panel Header Signal Names (J9G1) In/Out Out Out Description Hard disk LED pullup (330 ) to +5 V Hard disk active LED Pin Signal 2 4 In/Out Power LED HDR_BLNK_GRN Out HDR_BLNK_YEL Out Front panel green LED Front panel yellow LED Description Hard Drive Activity LED Reset Switch 5 7 9 Ground FP_RESET# +5 V In Out Ground Reset switch Power 6 8 10 Ground N/C On/Off Switch SWITCH_ON# In Power switch Ground Not connected 53 Intel Desktop Board D865PERL Product Guide Setting Up Full 6-Channel Surround Sound (Optional) After installing the SoundMAX* 4 XL audio driver from the Intel Express Installer CD-ROM, the multi-channel audio feature can be enabled. Figure 15 shows the location of back panel audio connectors. A B G F E DC OM16119 Item A B C D E F G Description Rear left/right out (multi-channel audio) Line in Line out (2-channel) or front left/right out (multi-channel) Mic in Center/Low Frequency Effects (LFE) out (multi-channel) Optical S/PDIF (Toslink) line out Coaxial S/PDIF (RCA) line out Figure 15. Back Panel Audio Connectors Multi-Channel Analog Audio Connect two speakers to the front left/right out (C) and two speakers to the rear left/right out (A) for both 4- and 6-channel audio configurations. For 6-channel audio, connect two additional speakers to the center LFE out (E). Multi-Channel Digital Audio Two types of S/PDIF connectors are available: coaxial (G) and optical (F). Select the proper connector according to the style of S/PDIF speakers that will be used. 54 Installing and Replacing Desktop Board Components Setting Up the Flexible 6-Channel Audio with Jack Sensing (Optional) After installing the SoundMAX 4 XL audio driver from the Intel Express Installer CD-ROM, the multi-channel audio feature can be enabled. A B C OM15694 Item A B C Description Rear left/right out or Line In Front left/right out or S/PDIF line out Center/LFE (Subwoofer) or Mic In Figure 16. Back Panel Audio Connectors for Flexible 6-Channel Audio System Multi-Channel Analog Audio Connect two speakers to the front left/right out (B) and two speakers to the rear left/right out (A) for both 4- and 6-channel audio configurations. For 6-channel audio, connect two additional speakers to the center LFE out (C). Multi-Channel Digital Audio To take advantage of the S/PDIF functionality, a 1/8-inch stereo phone plug to the RCA jack adapter/splitter is required to convert from the stereo input to RCA connection. Connect the stereo input side of the adapter to the S/PDIF (B) connector, and connect the speaker system or S/PDIF decoder to the RCA jack left channel (white, if colored). 55 Intel Desktop Board D865PERL Product Guide Connecting Hardware Control and Power Cables Figure 17 shows the location of the hardware control headers and power connectors. Chassis rear fan 12 V Processor core voltage connector 1 J5B1 VREG fan 2 J1B1 Processor fan J1F2 Chassis intrusion Chassis front fan Main power connector 2 1 J6J1 J6J2 OM15487 Figure 17. Location of Hardware Control and Power Connectors 56 Installing and Replacing Desktop Board Components Connecting Hardware Control Cables See Figure 17 for fan and chassis intrusion header locations. Connect the processor's fan heat sink cable to the processor fan header on the board. Connect chassis fan cables to the board fan headers. Connect the chassis intrusion cable to the respective header on the board. Connecting Power Cables CAUTION Failure to use an ATX12V power supply, or not connecting the 12 V processor core voltage power supply connector to the desktop board may result in damage to the desktop board and/or power supply. Figure 17 shows the location of the power connectors. Observe the precautions in "Before You Begin" on page 27. Connect the 12 V processor core voltage power supply cable to the 2x2 connector. Connect the main power supply cable to the 2x10 connector. 57 Intel Desktop Board D865PERL Product Guide Setting the BIOS Configuration Jumper Block CAUTION Always turn off the power and unplug the power cord from the computer before changing the jumper. Moving the jumper with the power on may result in unreliable computer operation. [. . . ] User must enter Setup. Error Message Memory Size Decreased Memory Size Increased Memory Size Changed No Boot Device Available Off Board Parity Error On Board Parity Error Parity Error NVRAM / CMOS / PASSWORD cleared by Jumper <CTRL_N> Pressed 105 Intel Desktop Board D865PERL Product Guide 106 B Regulatory Compliance This appendix contains information about safety standards, electromagnetic compatibility (EMC) regulations, and product certification markings for Desktop Board D865PERL. Safety Regulations Desktop Board D865PERL complies with the safety regulations stated in Table 45 when correctly installed in a compatible host system. Table 45. Regulation CSA C22. 2 No. 60950/ rd UL 60950, 3 Edition, 2000 EN 60950, 2 Edition, 1992 (with Amendments 1, 2, 3, and 4) IEC 60950, 2 edition, 1991 (with Amendments 1, 2, 3, and 4) EMKO-TSE (74-SEC) 207/94 nd nd Safety Regulations Title Bi-National Standard for Safety of Information Technology Equipment including Electrical Business Equipment. (USA and Canada) The Standard for Safety of Information Technology Equipment including Electrical Business Equipment. (European Union) The Standard for Safety of Information Technology Equipment including Electrical Business Equipment. [. . . ]