User manual INTEL D915GAG

[. . . ] Intel Desktop Board D915GEV/D915GUX/ D915GAV/D915GAG Product Guide Order Number: C64136-002 Revision History Revision -001 -002 Revision History First release of the Desktop Board D915GEV/D915GUX/ D915GAV/D915GAG Product Guide. Second release of Intel Desktop Board D915GEV/D915GUX/ D915GAV/D915GAG Product Guide. Intel Date June 2004 September 2004 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ] Place the VGA cover over the back panel VGA port (Figure 19, C). B A C OM16938 Figure 19. Inserting the PCI Express x16 Card and Covering the Back Panel VGA Port Removing the PCI Express x16 Card Follow these instructions to remove the PCI Express x16 card from the RM: 1. Observe the precautions in "Before You Begin" on page 27. Remove the screw that secures the card's metal bracket to the chassis back panel. Push back on the RM lever until the retention pin completely clears the notch in the card. Remove the VGA cover from the back panel VGA port. 41 Intel Desktop Board D915GEV/D915GUX/D915GAV/D915GAG Product Guide Connecting the IDE Cable The IDE cable can connect two drives to the desktop board. The cable supports the ATA-66/100 transfer protocol. Figure 20 shows the correct installation of the cable. NOTE ATA-66/100 compatible cables are backward compatible with drives using slower IDE transfer protocols. If an ATA-66/100 disk drive and a disk drive using any other IDE transfer protocol are attached to the same cable, the maximum transfer rate between the drives may be reduced to that of the slowest drive. NOTE Do not connect an ATA device as a slave on the same IDE cable as an ATAPI master device. For example, do not connect an ATA hard drive as a slave to an ATAPI CD-ROM drive. For correct function of the cable: Observe the precautions in "Before You Begin" on page 27. Attach the cable end with the single connector to the Intel desktop board (Figure 20, A). Attach the cable end with the two closely spaced connectors to the drives (Figure 20, B). A B OM16883 Figure 20. Connecting the IDE Cable 42 Installing and Replacing Desktop Board Components Connecting the Serial ATA (SATA) Cable The SATA cable (4-conductor) supports the Serial ATA protocol and connects a single drive to the desktop board. Either end of the cable can be connected to the SATA drive or the connector on the board. Observe the precaution in "Before You Begin" on page 27. Attach either cable end to the connector (Figure 21, A) on the board. Attach the other cable end to the drive (Figure 21, B). A B OM16897 Figure 21. Connecting the Serial ATA Cable 43 Intel Desktop Board D915GEV/D915GUX/D915GAV/D915GAG Product Guide Connecting Internal Headers Before connecting cables to the internal headers, observe the precautions in "Before You Begin" on page 27. Figure 22 shows the location of the internal headers. Port1L Port1R Port2R Sense_Send Port2L 1 3 2 4 GND Presence# Sense1_Ret Key (no pin) Sense2_Ret 56 7 9 10 E USB A Power (+5V) DD+ Ground Key (no pin) USB B Power (+5V) 3 4 D5 6 D+ 7 8 Ground 10 N/C 1 2 D 9 87 65 43 21 No Connection Reset HD LED 3 1 1 On/Off Power LED C Item A B C D E Description Chassis intrusion Power LED Front panel USB 2. 0 Front panel audio B A OM16918 Figure 22. Internal Headers 44 Installing and Replacing Desktop Board Components Installing a Front Panel Audio Solution Figure 22, E on page 44 shows the location of the yellow front panel audio header. Table 9 shows the pin assignments for the front panel audio header. Table 9. Pin 1 3 5 7 9 Front Panel Audio Header Signal Names Signal Name Port1L Port1R Port2R Sense Send Port2L Pin 2 4 6 8 10 Signal Name GND Presence# Sense1 Ret Key (no pin) Sense2 Ret To install the cable that connects the front panel audio solution to the front panel audio header, follow these steps: 1. [. . . ] Italiano Questo prodotto conforme alla Direttiva Europea 89/336/EEC & 73/23/EEC. Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 89/336/ EEC & 73/23/EEC. Portuguese Este produto cumpre com as normas da Diretiva Europia 89/336/EEC & 73/23/EEC. Espaol Este producto cumple con las normas del Directivo Europeo 89/336/EEC & 73/23/EEC. [. . . ]