User manual INTEL DESKTOP BOARD D510MO

[. . . ] Intel Desktop Board D510MO Product Guide Order Number: E74518-001 Revision History Revision -001 Revision History First release of the Intel Desktop Board D510MO Product Guide Date September 2009 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions related to the EMC performance of this product, contact: Intel Corporation, 5200 N. E. Elam Young Parkway, Hillsboro, OR 97124, 1-800-628-8686 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Connect the chassis fan cable to this header. Figure 13. Location of the Chassis Fan Header 39 Intel Desktop Board D510MO Product Guide Connecting the Power Supply Cable CAUTION Failure to use an appropriate power supply to the Desktop Board may result in damage to the board or the system may not function properly. Figure 14 shows the location of the power connector. Figure 14. Observe the precautions in "Before You Begin" on page 23. Connect the main power supply cable (2 x 12) to the 2 x 12 connector (Figure 14). 40 Installing and Replacing Desktop Board Components Setting the BIOS Configuration Jumper NOTE Always turn off the power and unplug the power cord from the computer before changing a jumper. Moving the jumper with the power on may result in unreliable computer operation. Figure 15 shows the location of the Desktop Board?s BIOS configuration jumper block. Figure 15. BIOS Configuration Jumper Block The three-pin BIOS jumper block enables board operating modes. Table 15 shows the jumper settings for each of the available modes. 41 Intel Desktop Board D510MO Product Guide Figure 15 shows the location of the Desktop Board?s BIOS configuration jumper block. Jumper Settings for the BIOS Setup Program Modes Jumper Setting Mode Normal (default) (1-2) Description The BIOS uses the current configuration and passwords for booting. Configure (2-3) After the Power-On Self-Test (POST) runs, the BIOS displays the Maintenance Menu. Use this menu to clear passwords. Recovery (None) The BIOS recovers data from a recovery diskette in the event of a failed BIOS update. Clearing Passwords This procedure assumes that the board is installed in the computer and the configuration jumper is set to normal mode. Observe the precautions in "Before You Begin" on page 23. Turn off all peripheral devices connected to the computer. Disconnect the computer?s power cord from the AC power source (wall outlet or power adapter). Find the configuration jumper block (see Figure 15, B). Place the jumper on pins 2-3 as shown below. 6. Replace the cover, plug in the computer, turn on the computer, and allow it to boot. Use the arrow keys to select Clear Passwords. Press <Enter> and Setup displays a pop-up screen requesting that you confirm clearing the password. Setup displays the maintenance menu again. Press <F10> to save the current values and exit Setup. 42 Installing and Replacing Desktop Board Components 10. Disconnect the computer?s power cord from the AC power source. [. . . ] Pay close attention to the following when reading the installation instructions for the host chassis, power supply, and other modules: ?Product certifications or lack of certifications External I/O cable shielding and filtering Mounting, grounding, and bonding requirements Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals, as applicable, are not Class B EMC compliant before integration, then EMC testing may be required on a representative sample of the newly completed computer. 64 Regulatory Compliance Product Certifications Board-Level Certification Markings Intel Desktop Board D510MO has the product certification markings shown in Table 24. Product Certification Markings Description UL joint US/Canada Recognized Component mark. Includes adjacent UL file number for Intel Desktop Boards: E210882. [. . . ]