User manual INTEL DESKTOP BOARD DG41AN

[. . . ] Intel Desktop Board DG41AN Product Guide Order Number: E95580-001 Revision History Revision -001 Revision History First release of the Intel Desktop Board DG41AN Product Guide Date June 2010 Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL?S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. [. . . ] Front Panel Audio Signal Names for Intel HD Audio Pin 1 3 5 7 9 Signal Name PORT 1L (Microphone) PORT 1R (Microphone) PORT 2R (Headphone) SENSE_SEND PORT 2L (Headphone) Pin 2 4 6 8 10 Signal Name GND PRESENCE# SENSE1_RETURN KEY (no pin) SENSE2_RETURN Table 7. Front Panel Audio Header Signal Names for AC?97 Audio Pin 1 3 5 7 9 Signal Name MIC MIC_BIAS FP_OUT_R AUD_5V FP_OUT_L Pin 2 4 6 8 10 Signal Name AUD_GND AUD_GND FP_RETURN_R KEY (no pin) FP_RETURN_L Chassis Intrusion Header Figure 18, B on page 38 shows the location of the chassis intrusion header. This header can be connected to a mechanical switch on the chassis to detect if the chassis cover is removed. Table 8 shows the pin assignments for the chassis intrusion header. Chassis Intrusion Header Signal Names Pin 1 2 Description Intruder Ground 39 Intel Desktop Board DG41AN Product Guide Serial Port Header See Figure 18, C on page 38 for the location of the serial port header. Table 9 shows the pin assignments for the serial port header. Serial Port Header Signal Names Pin 1 3 5 7 9 Signal Name DCD TXD# Ground RTS RI Pin 2 4 6 8 10 Signal Name RXD# DTR DSR CTS No Connection USB 2. 0 Headers Before connecting to the USB 2. 0 headers, observe the precautions in "Before You Begin" on page 24. See Figure 18, D on page 38 for the location of the USB 2. 0 headers. Table 10 shows the pin assignments for each USB 2. 0 header. Each USB header can be used to connect two USB devices. USB 2. 0 Header Signal Names USB Port A Pin 1 3 5 7 9 Signal Name Power (+5 V) DD+ Ground Key Pin 2 4 6 8 10 USB Port B Signal Name Power (+5 V) DD+ Ground No Connection Note: USB ports may be assigned as needed. NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. 40 Installing and Replacing Desktop Board Components Alternate Front Panel Power LED Header Figure 18, E on page 38 shows the location of the alternate front panel power LED header. Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header. If your chassis has a three-pin power LED cable, connect it to this header. Table 11 shows the pin assignments for the alternate front panel power LED header. Alternate Front Panel Power LED Header Signal Names Pin 1 2 3 Description Front panel green LED No pin Front panel yellow LED Out In/Out Out Front Panel Header Before connecting to the front panel header, observe the precautions in "Before You Begin" on page 24. See Figure 18, F on page 38 for the location of the multi-colored front panel header. Table 12 shows the pin assignments for the front panel header. Front Panel Header Signal Names Pin 1 3 5 7 9 Description Hard Drive Activity LED Hard disk LED pull-up to +5 V Out Hard disk active LED Reset Switch Ground Reset switch Power Power Out 10 No pin In 6 8 Ground Not Connected Out 2 4 In/Out Pin Description Power LED Front panel green LED Front panel yellow LED On/Off Switch Power switch In Out Out In/Out 41 Intel Desktop Board DG41AN Product Guide Connecting to the Back Panel Audio Connectors After the audio driver has been installed, the multi-channel audio feature can be enabled. Figure 19 shows the back panel audio connectors. The default connector assignments are shown in the figure. Refer to Table 4 on page 16 for audio connector retasking information. Item A B C Description Line In Line Out Mic In Figure 19. [. . . ] Japan VCCI (Voluntary Control Council for Interference) mark. S. Korea KCC (Korean Communications Commission) mark. Includes adjacent KCC certification number: CPU-DG41AN (B). Taiwan BSMI (Bureau of Standards, Metrology and Inspections) mark. Includes adjacent Intel company number, D33025. [. . . ]