User manual INTEL DESKTOP BOARD DH61WW

[. . . ] Intel Desktop Board DH61WW Product Guide Order Number: G23562-002 Revision History Revision -001 -002 Revision History First release of the Intel Desktop Board DH61WW Product Guide Second release of the Intel Desktop Board DH61WW Product Guide Date February 2011 April 2011 Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL?S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. [. . . ] Front Panel Audio Header Signal Names for AC ?97 Audio Pin 1 3 5 7 9 Signal Name MIC MIC_BIAS FP_OUT_R No connection FP_OUT_L Pin 2 4 6 8 10 Signal Name AUD_GND PRESENCE# AUD_GND KEY (no pin) AUD_GND S/PDIF Header Figure 18, B shows the location of the S/PDIF output header. Table 6 shows the pin assignments and signal names for the S/PDIF output header. S/PDIF Header Signal Names Pin 1 2 3 4 Description Ground S/PDIF Out Key (no pin) +5 VDC 44 Installing and Replacing Desktop Board Components Chassis Intrusion Header Figure 18, C shows the location of the chassis intrusion header. This header can be connected to a mechanical switch on the chassis to detect if the chassis cover is removed. This switch should be in the open position when the chassis cover is installed and closed when the cover is removed. Table 7 shows the pin assignments and signal names for the chassis intrusion header. Chassis Intrusion Header Signal Names Pin 1 2 Description Intruder# Ground TPM Header The TPM header is shown in Figure 18, D. Table 8 shows the pin assignments and signal names for the TPM header. TPM Header Signal Names Pin 1 3 5 7 9 11 13 15 17 19 Signal Name CK_33M_TPM_DIP LFRAME# PLTRST# LAD3 +3. 3 V LAD0 No connection +3. 3 VSB Ground LPCPD# Pin 2 4 6 8 10 12 14 16 18 20 Signal Name Ground Key (no pin) No connection LAD2 LAD1 Ground No connection TPM_SERRQ TPM_CLKRUN# No connection 45 Intel Desktop Board DH61WW Product Guide Front Panel Header Figure 18, E shows the location of the front panel header. Table 9 shows the pin assignments and signal names for the front panel header. Front Panel Header Signal Names Pin 1 3 5 7 9 Description In/Out Pin 2 4 6 In Power Power Out 10 No pin 8 Description Power LED Front panel LED+ Front panel LEDOn/Off Switch Power switch Ground Not Connected In Out Out In/Out Hard Disk Drive Activity LED Hard disk LED pull-up to +5 V Out Hard disk active LED Reset Switch Ground Reset switch Out NOTE When connecting individual wires from your chassis front panel to the front panel header, be sure to observe the connection polarity. Positive wires are usually solid color and negative wires are usually white or striped. Serial Header Figure 18, F shows the location of the serial header. Table 10 shows the pin assignments and signal names for the serial header. Serial Port Header Signal Names Pin 1 3 5 7 9 Signal Name DCD (Data Carrier Detect) TXD# (Transmit Data) Ground RTS (Request To Send) RI (Ring Indicator) Pin 2 4 6 8 10 Signal Name RXD# (Receive Data) DTR (Data Terminal Ready) DSR (Data Set Ready) CTS (Clear To Send) Key (no pin) 46 Installing and Replacing Desktop Board Components Front Panel USB 2. 0 Header Figure 18, G shows the location of the front panel USB 2. 0 header and Table 11 shows the pin assignments and signal names. Front Panel USB 2. 0 Header Signal Names Pin 1 3 5 7 9 Signal Name Power (+5 V) DD+ Ground Key Pin 2 4 6 8 10 Signal Name Power (+5 V) DD+ Ground No Connection NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. 47 Intel Desktop Board DH61WW Product Guide Connecting to the Audio System After installing the Realtek audio driver from the Intel Express Installer DVD-ROM, the multi-channel audio feature can be enabled. Figure 19 shows the back panel audio connectors. The default connector assignments are shown in the table. Item A B C Description Line in Line out (front speaker/headphones) Mic in Figure 19. Back Panel Audio Connectors NOTE The back panel line out connector is designed to power either headphones or amplified speakers only. Poor audio quality may occur if passive (non-amplified) speakers are connected to this output. 48 Installing and Replacing Desktop Board Components Connecting Chassis Fan and Power Supply Cables Connecting a Chassis Fan Cable Connect chassis fan cables to the chassis fan header on the Desktop Board. Figure 20 shows the location of the chassis fan header. Figure 20. Location of the Chassis Fan Header 49 Intel Desktop Board DH61WW Product Guide Connecting Power Supply Cables CAUTION Failure to use an appropriate power supply and/or not connecting the 12 V power connector (Figure 21, A) to the Desktop Board may result in damage to the board or the system may not function properly. [. . . ] Japan VCCI (Voluntary Control Council for Interference) mark. Korea Certification mark. Includes an adjacent KCC (Korean Communications Commission) certification number: KCC-REM-CPU-DH61WW (B). Taiwan BSMI (Bureau of Standards, Metrology and Inspections) mark. Includes adjacent Intel company number, D33025. [. . . ]