User manual INTEL DESKTOP BOARD DP67BA

[. . . ] Intel Desktop Board DP67BA Product Guide Order Number: G14707-001 Revision History Revision -001 Revision History First release of the Intel Desktop Board DP67BA Product Guide Date October 2010 Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL?S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. [. . . ] The receiver header consists of a filtered translated infrared input compliant with Microsoft CIR specifications and a ?learning?The learning input is a high-pass input which the computer can use to ?learn?to speak the infrared communication language of other user remotes. The emitter header consists of two output ports which the computer can use to emulate ?learned?infrared commands in order to control external electronic hardware. NOTE The Consumer IR option must be enabled in the system BIOS before it can function. Press <F2> at boot to enter the system BIOS, and go to Advanced > Peripheral Configuration > Enhanced Consumer IR, and set this option to Enabled. Table 9 shows the pin assignments for the front panel CIR receiver (input) header and Table 10 shows the pin assignments for the back panel CIR emitter (output) header. Front Panel CIR Receiver (Input) Header Signal Names Pin 1 3 5 7 Signal Name Ground No Connection +5 V Standby Key (no pin) Pin 2 4 6 8 Signal Name LED Learn-In Vcc CIR Input 44 Installing and Replacing Desktop Board Components Table 10. Back Panel CIR Emitter (Output) Header Signal Names Pin 1 3 5 Signal Name Emitter Out 1 Ground Jack Detect 1 Pin 2 4 6 Signal Name Emitter Out 2 Key (no pin) Jack Detect 2 Alternate Front Panel Power LED Header Figure 20, F shows the location of the alternate front panel power LED header. Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header. If your chassis has a three-pin power LED cable, connect it to this header. Table 11 shows the pin assignments for the alternate front panel header. Alternate Front Panel Power LED Header Signal Names Pin 1 2 3 Signal Name Front panel LED+ No pin Front panel LEDOut In/Out Out Front Panel Header Figure 20, G shows the location of the front panel header. Table 12 shows the pin assignments and signal names for the front panel header. Front Panel Header Signal Names Pin 1 3 5 7 9 Description Hard Drive Activity LED Hard disk LED pull-up to +5 V Out Hard disk active LED Reset Switch Ground Reset switch Power Power Out 10 No pin In 6 8 Ground Not Connected Out 2 4 In/Out Pin Description Power LED Front panel LED+ Front panel LEDOn/Off Switch Power switch In Out Out In/Out NOTE When connecting individual wires from your chassis front panel to the front panel header, be sure to observe the connection polarity. Positive wires are usually solid color and negative wires are usually white or striped. 45 Intel Desktop Board DP67BA Product Guide Front Panel USB 2. 0 Headers Figure 20, H shows the location of the front panel USB 2. 0 headers and Table 13 shows their pin assignments and signal names. USB 2. 0 Header Signal Names Pin 1 3 5 7 9 Signal Name Power (+5 V) DD+ Ground Key Pin 2 4 6 8 10 Signal Name Power (+5 V) DD+ Ground No Connection NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. S/PDIF Header Figure 20, I shows the location of the S/PDIF output header. Table 14 shows the pin assignments and signal names for the S/PDIF output header. S/PDIF Header Signal Names Pin 1 2 3 4 Description Ground S/PDIF Out Key (no pin) +5 VDC 46 Installing and Replacing Desktop Board Components Connecting to the Audio System After installing the Realtek audio driver from the Intel Express Installer DVD-ROM, the multi-channel audio feature can be enabled. Figure 21 shows the back panel audio connectors. The default connector assignments are shown in the table. Item A B C D E F Description Rear surround Center channel and LFE (subwoofer) S/PDIF out optical Audio line in Mic in Front speakers (line out) Figure 21. [. . . ] Japan VCCI (Voluntary Control Council for Interference) mark. S. Korea KCC (Korean Communications Commission) mark. Includes adjacent KCC certification number: CPU-DP67BA (B). Taiwan BSMI (Bureau of Standards, Metrology and Inspections) mark. Includes adjacent Intel company number, D33025. [. . . ]