User manual INTEL DESKTOP BOARD DX58SO

[. . . ] Intel Desktop Board DX58SO Product Guide Order Number: E43167-002 Revision History Revision -001 -002 Revision History First release of the Intel Desktop Board DX58SO Product Guide Second release of the Intel Desktop Board DX58SO Product Guide Date August 2008 May 2010 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions related to the EMC performance of this product, contact: Intel Corporation, 5200 N. E. Elam Young Parkway, Hillsboro, OR 97124 1-800-628-8686 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] This header can be connected to a mechanical switch on the chassis to detect if the chassis cover is removed. Table 8 shows the pin assignments and signal names for the chassis intrusion header. Chassis Intrusion Header Signal Names Pin 1 2 Description Intruder Ground IEEE 1394a Header Figure 27, F shows the location of the IEEE 1394a header. Table 9 shows the pin assignments and signal names for the IEEE 1394a header. IEEE 1394a Header Signal Names Pin 1 3 5 7 9 Signal Name TPA1+ Ground TPA2+ +12 V Key (no pin) Pin 2 4 6 8 10 Signal Name TPA1Ground TPA2+12 V Ground 49 Intel Desktop Board DX58SO Product Guide USB 2. 0 Headers Figure 27, G shows the location of the USB 2. 0 headers. Table 10 shows the pin assignments and signal names for each USB 2. 0 header. Each USB header can be used to connect two USB devices. USB 2. 0 Header Signal Names USB Port A Pin 1 3 5 7 9 Signal Name Power (+5 V) DD+ Ground Key Pin 2 4 6 8 10 USB Port B Signal Name Power (+5 V) DD+ Ground No Connection Note: USB ports may be assigned as needed. NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. Front Panel Header Figure 27, I shows the location of the front panel header. Table 11 shows the pin assignments and signal names for the front panel header. Front Panel Header Signal Names Pin 1 3 5 7 9 Description Hard Drive Activity LED Hard disk LED pull-up to +5 V Out Hard disk active LED Reset Switch Ground Reset switch Power Power Out 10 No pin In 6 8 Ground Not Connected Out 2 4 In/Out Pin Description Power LED Front panel green LED Front panel yellow LED On/Off Switch Power switch In Out Out In/Out 50 Installing and Replacing Desktop Board Components Alternate Front Panel Power LED Header Figure 27, H shows the location of the alternate front panel power LED header. Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header. If your chassis has a three-pin power LED cable, connect it to this header. Table 12 shows the pin assignments and signal names for the alternate front panel power LED header. Alternate Front Panel Power LED Header Signal Names Pin 1 2 3 Description Front panel green LED No pin Front panel yellow LED Out In/Out Out S/PDIF Connector Figure 27, J shows the location of the S/PDIF connector. This connector can be used with HDMI video cards that do not work with the HD Audio Link header (see Figure 27, B). Table 13 shows the pin assignments and signal names for the S/PDIF connector. S/PDIF Connector Signal Names Pin 1 2 3 Description Vcc S/PDIF Out Ground 51 Intel Desktop Board DX58SO Product Guide Connecting to the Audio System After installing the RealTek audio driver from the Intel Express Installer DVD-ROM, the multi-channel audio feature can be enabled. Figure 28 shows the back panel audio connectors. The default connector assignments are shown in the table. Item A B C D E F Description Surround Left and Right Center Channel and LFE (Subwoofer) Side Surround Left and Right/Line In/Retasking Jack Line Out Mic In S/PDIF Digital Audio Out (Optical) Figure 28. Back Panel Audio Connectors NOTE The back panel line out connector is designed to power either headphones or amplified speakers only. Poor audio quality may occur if passive (non-amplified) speakers are connected to this output. 52 Installing and Replacing Desktop Board Components Connecting Chassis Fan and Power Supply Cables Connecting Chassis Fan Cables Connect chassis fan cables to the 3-pin and 4-pin chassis fan headers on the Desktop Board. [. . . ] Product certifications or lack of certifications External I/O cable shielding and filtering Mounting, grounding, and bonding requirements Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals, as applicable, are not Class B EMC compliant before integration, then EMC testing may be required on a representative sample of the newly completed computer. 83 Intel Desktop Board DX58SO Product Guide Product Certifications Board-Level Certification Markings Intel Desktop Board DX58SO has the product certification markings shown in Table 21. Product Certification Markings Description UL joint US/Canada Recognized Component mark. Includes adjacent UL file number for Intel Desktop Boards: E210882. FCC Declaration of Conformity logo mark for Class B equipment. [. . . ]