User manual INTERMATIC 158SS11366

[. . . ] Note: THE REMOTE SWITCH(ES) MAY NOT FUNCTION RELIABLY WHEN THE ACCUMULATED WIRE LENGTH TO THE REMOTE SWITCH(ES) EXCEEDS 200 FEET OR IF THE WIRING TO THE REMOTE SWITCH(ES) IS BURIED UNDERGROUND. Note: Used remote switches from a previous conventional installation may not function reliably with an electronic timer. Try a brand new remote switch if function is intermittent. Wiring diagram, 2 switch installation (3-way) JUMPER BLUE BLACK LINE TIMER RED 3-WAY SWITCH RED SINGLE POLE SWITCH Wiring diagram, 2 switch installation (3-way) using a single pole remote switch LOAD BLUE LOAD NEUTRAL BLACK LINE TIMER NEUTRAL For new construction or to replace a dimmer switch a lighted switch or a 3-way switch without screw terminals, a single pole switch can be used at the remote location as shown. Wiring diagram, 3 switch installation For 3 or more switch operation, AN ADDITIONAL WIRE MUST BE ADDED between the load and the timer. [. . . ] As with the timer, there is a brief delay before the load turns off. Allow at least 2 seconds for the timer to respond to the remote switch. 4. 5. Single Switch ­ (See below) Connect one of the house wires to the black wire from the timer, using the wire nuts provided. Connect the other house wire to the blue wire from the timer. THERED WIRE IS RED WIRE NOT USED FOR SINGLE (CAPPED, NOT CONNECTED) SWITCH INSTALLATIONS. Make sure that all wire nuts are secure. 3-way Switch ­ (See below) (See "Other Installations" to use a dimmer or if switching from 3 or more locations). A 3-way switch has three wires connected to it. One of the wires is "common" (the terminal has a different colored screw or there are markings on the old switch). Single Switch Installation 3-Way Switch Installation BLACK WIRE RED WIRE BLUE WIRE WIRE FROM "COMMON" OF OLD SWITCH COMMON MOVE JUMPER WIRE TO OTHER TERMINAL IF THIS SWITCH DOES NOT TURN LIGHT ON RED WIRE (CAPPED, NOT CONNECTED) BLUE WIRE 7/16" BLACK WIRE TRIM HOUSE WIRES BARE TO 7/16" REMOTE 3-WAY SWITCH EI40C/EI40AC Electronic Automatic Shut-Off Timer Installing / Changing the Battery To remove the battery cover, use a standard screwdriver in the bottom notch to gently pry the cover away from the housing. To reinstall, place battery in holder with "+" end towards the front of the timer. Insert battery and cover and push at the top so it clicks into place. LCD DISPLAY 10:00 KEYPAD Controls, Displays and Operation Cover/ Switch ­ Pressing and releasing the clear cover/switch starts the interval timing functions. Press either key individually to increase/decrease the preset time. The time scrolls faster when the key is held longer. Pressing both keys simultaneously causes the timer to sequence through the preset times of 5, 10, 15, 30 minutes and 1, 2, 4, 6, 8, 12 and 24 hours. Once a preset time has been set, it can be modified using the and/or keys individually. RESET ­ Used to reset the timer in the event it displays "noOP" or other meaningless information. Does not alter the preset time. EI40C Operation/Display/Keypad Load Maintenance WARNING!DO NOT USE THE TIMER TO TURN OFF POWER FOR MAINTENANCE (service, repairs, broken bulbs, etc. ). ALWAYS TURN OFF POWER AT THE SERVICE PANEL BY REMOVING A FUSE OR SWITCHING OFF A CIRCUIT BREAKER BEFORE DOING ANY CIRCUIT REPAIRS. OFF 23:28 OFF 23:28 Normal display when timer has timed out. 23:28 OFF LOW BATTERY ON LOW BATTERY ON LOW BATTERY LOW BATTERY ON ON LOW BATTERY ON Warns that battery needs replacing soon. HOL LOW BATTERY ON ON CAUTION: This timer should not be used in precision timing applications where inaccurate timing could have dangerous consequences (i. e. , sun lamps, sauna, etc. ) HOL 23:28 HOL HOLD OP Displays when HOLD is pressed and timer is OP ON indefinitely. OP 23:28 HOL 23:28 23:28 OFF 23:28 23:28 Normal display when timing out. [. . . ] For example, to set 9 minutes, use the Quick Set feature to select 10 minutes, then scroll the time down to 9 minutes using the key. How do I restart the timer without switching OFF the load?Pressing the ON/OFF key twice in less than 1 second or operating the remote switch twice in less than 1 second (for 3-way applications) when the load is ON will restart the timed interval without switching off the load. This is desirable when controlling HID lighting. [. . . ]