User manual INTERQUARTZ VOYAGER MEMORY PHONE

[. . . ] Telephone Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Store Button (underneath overlay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Ringer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Ringer Volume Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If too many phones are connected to the line, the circuit may be overloaded and your telephone may not ring. If a British Telecom phone is supplied unmarked, you can assume that it has a REN of 1 Emergency calls Calls can be made on this telephone to contact the emergency services. The European code for emergency services is 112, however, you can still use 999 in the UK. An access code may also be required, if the phone is connected to a PABX. 3 2. Installation This telephone is designed to plug straight into a modular style socket. If you do not have one of these sockets, they can be obtained from your Network Supplier. Connection Insert the line cord into the socket. Set the ringer volume control, and ringer pitch adjust as desired. Wall mounting Using the template supplied, position the telephone where you want to wall mount. Drill two holes and fix roundheaded screws, leaving them slightly proud of the surface. Position the telephone over the screws and slide downwards into place. FOR WALL MOUNT Figure 1 Wall Mounting 4 To enable the handset to be supported in the cradle when the phone is mounted on the wall, follow the procedure shown in Figure 3 to reserve the HANDSET RETAINER. 1. Use screw-driver to push the HANDSET RETAINER 2. Push the HANDSET RETAINER out of the slot 3. Insert the HANDSET RETAINER back into it's slot Figure 2 Handset Retainer for Wall Mounting 5 3. Telephone Features UNDERNEATH OVERLAY STORE KEY UNDERNEATH OVERLAY PROGRAM SOCKET RINGER INDICATOR (WITH MESSAGE WAIT) HANDSET MEMORY KEY HANDSET CORD KEY PAD REDIAL / PAUSE KEY RECALL KEY Figure 3 General Appearance To help you find your way round the telephone, various features and buttons are briefly described below. You should refer to the relevant section of this user guide to learn how to use the features available. Store Button (underneath overlay) Used to store numbers into the direct access memory buttons. Ringer Indicator Flashes when the telephone rings with an incoming call. Ringer Volume Switch Located on the base of the unit (see Figure 4). Move switch to select no sound (OFF), muted sound (LOW) or full sound (HIGH) for ringing on incoming call. 6 Ringer Pitch Control On the base of the unit. Allows the pitch of the ringer to be altered from a high pitch to a low pitch. Recall Button For PABX use, to carry out call transfers and access other PABX facilities. Memory Stores There are 10 buttons able to retrieve 10 memory locations, each able to store 32 digits. Redial / Pause Button If pressed once the dial tone is heard, the last number dialled with capacity of 32 digits will be redialled. Otherwise , it serves as a pause button inserting a 3. 6 second pause in the number sequence. LINE JACK DATA JACK RINGER PITCH ADJUST SWITCH RINGER PITCH HEADSET MIC ADJUST RINGER HI / LOW / OFF Figure 4 Bottom View 7 TBR TIMED BREAK / EARTH RECALL SWITCH UNPLUG THE CONNECTION TO THE NETWORK BEFORE OPENING THIS COVER VOICE MESSAGING ( N / S2 / S1 ) SWITCH ER S1 S2 N 4. Operation To dial a number, either lift the handset , wait for the dial tone and then key in the number required. Answering a call You can answer a call by simply lifting the handset. Manual Dialling Lift the handset, listen for the dial tone and then dial the required number using the keypad. Memory Storage / Dialling This telephone can store ten memories. The numbers are stored in flash memory which means that they will never be lost. To store numbers, ensure that the telephone is connected to the line. · · · · · · either lift the handset press the store button dial the number to be stored using the keypad press the store button again press the memory button where you want to save the number replace the handset to clear the line. To dial numbers from memory · either lift the handset · once dial tone is present press the required memory button, the stored number will then be dialled automatically. Redial / Pause Function Redial If the number dialled is busy, 8 · hang-up and obtain a new line by either lifting the handset . · press the button labelled redial/pause and the last number (up to 32 digits) that you dialled will automatically be redialled. Pause The Pause command may be needed if the phone is connected to certain types of PABX or to any network where a pause is required. [. . . ] - REN number may exceed 4, disconnect a phone until the number is below 4. If there are still problems, and you have more than one telephone: Remove the "problem" phone. Insert another phone and check that it works. If "yes" then the "problem" phone is possibly faulty. [. . . ]