User manual IOGEAR GCL1800 INSTALLATION

[. . . ] 9. External PS/2 Mouse Port External PS/2 Keyboard Port External VGA Port CPU Port 4 6 Console PS/2-USB CPU 1 2 3 5 7 8 9 Back view 7 Rack Mounting The following diagram shows the required components to mount the LCD Console to the rack. L Bracket CAUTION: Slide/rail mounted equipment is not to be used as a shelf or a work space. Side Mounting Brackets Note: The Slide Mounting Brackets are pre-installed onto the LCD Console. 8 Step 1 While one person holding the LCD Console in the proper position in the rack, the second person can lock the screws loosely through the front bracket onto the front of the rack. M4 x 6 Phillips Head Screws 9 Step 2 While the person continue holding the position of the LCD Console, the second person can slide the L brackets from the back of the rack into the Slide Mounting Brackets. Then, you can lock the screws through the rear bracket onto the back of the rack. M4 x 6 Phillips Head Screws Final Step After the rear brackets are completely secured, tighten the front brackets' screws. 10 Grounding To prevent damaging your equipment, it is important that all devices are properly grounded. Use the included grounding wire to ground the LCD Console by connecting one end of the wire to the grounding terminal, and the other end of the wire to a suitable grounded object. Console PS/2-USB CPU 11 Open/Close Console Opening the Console Slide the 2 Slide Releases toward the center of the LCD Console, then pull the console module out while holding the Slide Releases' position. [. . . ] Then turn on the LCD Console by the power switch that's located in the back of the LCD Console. Step 3 Go to www. iogear. com to download the latest available firmware or the specific firmware that you wish to upgrade to. Step 4 Make sure the computer that is connected to the LCD Console is completely shutdown. (Please refer to Hotkey Commands Section) Step 5 Extract the file that you have downloaded by using software such as Winrar. Then double-click on the execute file to open up the Firmware Upgrade Utility. 29 Step 6 Read the License Agreement and click "I Agree" then click "Next" if you wish to continue with the firmware upgrade. Otherwise, click "Cancel" to exit. Step 7 Choose the correct device* that you wish to perform firmware upgrade from the "Device List" and then click "Next" to continue. Then the Firmware Upgrade Utility will verify if the device is connected to the computer via the firmware upgrade cable. (Check Firmware Version checkbox is optional) 30 *Note: Please choose MAIN to proceed the firmware upgrade. KB is a sub layer in the LCD Console firmware. Step 8 If you have checked the "Check Firmware Version" checkbox, then the utility will check the current firmware that is on your LCD Console. · Do not place the device on any unstable surface (cart, stand, table, etc. ). If the device falls, serious damage may result. · Do not use the device near water. · Do not place the device near or over any radiator, heat register or other heat source. · The device cabinet is equipped with ventilation openings to ensure that the device remains adequately ventilated and does not overheat. These openings must never be blocked or covered. · The device should never be placed on a soft surface (bed, sofa, rug, etc. ) as this will block the ventilation openings. Additionally, the device should not be placed inside another enclosure (bookcase, etc. ) unless adequate ventilation is provided. · Do not place any liquids on top of the device and take all precautions to avoid spilling any liquids on the device. · Unplug the device from the wall outlet before cleaning. Use only a lightly dampened cloth for cleaning. · The device should only be operated from the type of power source indicated on the label. If you are not sure what type of power is available, consult your dealer or local power company. [. . . ] Operating this product in a residential area will likely cause harmful interference which will require correction by the user at his/her personal expense. 39 CE Statement This device has been tested and found to comply with the requirements set up in the council directive on the approximation of the law of member states relating to EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC and R&TTE Directive 99/5/EC. The product has been approved for LVD and covered the following countries: Belgium, Denmark, France, Germany, Italy, Portugal, U. K. , Spain, Sweden 40 SJ/T 11364-2006 The following contains information that relates to China. (Pb) (Hg) Cd (Cr(VI)) PBB PBDE :SJ/T 11363-2006 : SJ/T 11363-2006 ×: SJ/T 11363-2006 41 Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK, OR ITS DOCUMENTATION EXCEED THE PRICE PAID FOR THE PRODUCT. The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect to the contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or fitness for any particular purpose. The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions, or updates. [. . . ]