User manual IOGEAR GCS24U QUICKSTART GUIDE

[. . . ] Please refer to Hotkey Summary Table for details. *Note:Ifthereisaconflictusing[ScrollLock][ScrollLock]sequence, youcanchangetothealternative sequence [Ctrl] [Ctrl]. Please refer to Hotkey Setting Mode (HSM) section for details. 15 Hotkeys Summary Table Hotkey combination [Scroll Lock] [Scroll Lock] + or [Ctrl] [Ctrl]* + *Note: If alternative hotkey sequence is chosen [Enter] [n*] [Enter] [k] [Enter] [n*] [k] [Enter] [u] [Enter] [n*] [u] [Enter] [s] [Enter] [n*] [s] [Enter] [n*] [k] [s] [Enter] [n*] [k] [u] [Enter] [n*] [u] [s] [Enter] Description Switch KVM, USB and audio focus to the next port SwitchKVM, USBandaudiofocustothespecificport Switch KVM focus to the next port SwitchKVMfocustothespecificport Switch USB focus to the next port SwitchUSBfocustothespecificport Switch audio focus to the next port Switchaudiofocustothespecificport SwitchKVMandaudiofocustothespecificport SwitchKVMandUSBfocustothespecificport SwitchUSBandaudiofocustothespecificport *Note: Interval n is the port ID number (1 and 2 for GCS24U and 1, 2, 3 and 4 for GCS1104) 16 Autoscan Mode You can either activate Autoscan Mode via front panel push button or hotkeys. Function Auto Scan Description Front Panel Push Button Press and hold port 1 and port 2 Pushbutton simultaneously for 2 seconds to activate Autoscan Mode* Hotkeys [Scroll Lock] [Scroll Lock] [a] Activate Autoscan mode. [. . . ] It [Enter] will cycle from port to port every 5 seconds (default) [Scroll Lock] [Scroll Lock] [a] Activate Autoscan mode. It [n] [Enter] will cycle from port to port every n seconds** *Note: Autoscan Mode from front panel push button will be scanning a port every 5 seconds by default. If you wish to have the Autoscan Mode be scanning with different time interval, please trigger Autoscan Mode via hotkeys. **Note: n is an interval between 1 and 99 that stands for the time (in second) desire for scanning each port. 17 Hotkey Setting Mode (HSM) Hotkey 1. Press and hold [Num Lock] ([Clear] key on Mac keyboard) 2. Release [Num Lock] ([Clear] key on Mac keyboard) Invoke HSM, then press [h] Invoke HSM, then press [t] Invoke HSM, then press [F2] Invoke HSM, then press [F3] Invoke HSM, then press [F10] Description Invoking hotkey setting mode Invoke HSM, then press [F4] Change the HSM invocation keys from [Num Lock] to [Ctrl] and from [-] to [F12] Change port switching hotkey sequence between [Scroll Lock] [Scroll Lock] and [Ctrl] [Ctrl] Enables Mac keyboard emulation Enables Sun keyboard emulation Auto-detect the keyboard operating platform (for PC compatible systems). Activates Pass Through Keyboard Mode (keystrokes are sent directly to the computer instead of through the Mac emulator). List out current settings Note: Please have a Notepad or word document opened before you trigger this function. 18 Invoke HSM, then press [F5] Invoke HSM, then press [b] Invoke HSM, then press [s] Invoke HSM, then press [x] [Enter] Invoke HSM, then press [u] [p] [g] [r] [a] [d] [e] [Enter] Invoke HSM, then press [r] [Enter] Invoke HSM, then press [d] Invoke HSM, then press [m] Invoke HSM, then press [F1] USB Reset Toggle hotkey beepers on or off Toggle front panel pushbutton between Mode1 and Mode2 Disable or enable port switching hotkey Activate Firmware Upgrade Mode ­ Front panel KVM LED will flashindicatingFirmwareUpgradeModeisactivated. Restore default settings Captureandstoremonitor'sEDIDonspecificport Enable or disable mouse emulation Reset keyboard and mouse under some special OS' that do not support USB 2. 0 *Note: To exit HSM manually, press Esc or spacebar. 19 Mac Keyboard Emulation The PC compatible (101/104 key) keyboard can emulate the functions of the Mac keyboard. ***VGA Female to DVI-A Male Adapter (GDVIMVGAF) is available and sold separately at www. iogear. com. If you meet all the requirements above, then you can follow the below instructions to setup your KVM. Please make sure all devices are turned off before you start. 29 For the DVI computers: Simply follow the instruction of the Installation Section. Connect each of your VGA video output with a VGA Male to Male cable. Connect the other side of the VGA cable to the VGA connection on the DVI-A Male to VGA Female Adapter. Connect the DVI-A connection to the CPU DVI port of the KVM. Then use the provided DVI-D KVM cable for USB, audio and mic. For the Console DVI Port Connect the DVI-I cable from the Console DVI port to the monitor. 30 FCC Statements 15. 21 Youarecautionedthatchangesormodificationsnotexpresslyapprovedbythepartresponsiblefor compliance could void the user's authority to operate the equipment. 15. 105(b) his equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. [. . . ] For the Console DVI Port Connect the DVI-I cable from the Console DVI port to the monitor. 30 FCC Statements 15. 21 Youarecautionedthatchangesormodificationsnotexpresslyapprovedbythepartresponsiblefor compliance could void the user's authority to operate the equipment. 15. 105(b) his equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ]