User manual IOGEAR GCS661U INSTALLATION GUIDE

[. . . ] "Slave Computer" refers to the computer that is being accessed remotely by the Master Computer. 5 Overview 1. USB 2. 0 Connection for the Slave Computer (longer) 2. USB 2. 0 Connection for the Master Computer (shorter) 4. USB 2. 0 Peripheral Port for Master Computer 1 2 3 4 6 Before You Start If you wish the Slave Computer to be ready for access every time after booting up or after GCS661U is plugged in without the present of a monitor, keyboard and mouse connected to the Slave Computer, the following procedures are required: 1. [. . . ] You can connect any USB device to it and the device can be used as if it is connected directly to the Master Computer. Note: If you are connecting a USB harddrive to the USB 2. 0 peripheral port, an external power supply for the harddrive is required. 17 Fullscreen Mode If Fullscreen Mode is being used, an auto-hide bar will show up if you move the cursor to the top middle of the screen as the image shown. 1 No. 1 2 3 4 5 Name Pin Board Pin Slave Computer's Name Minimize Window Toggle Fullscreen Mode Close Window Description 2 345 Pin/unpin auto-hide bar from the fullscreen Shows the Slave Computer's name Minimize the fullscreen window Disable/enable Fullscreen Mode Close the window and disconnect from the Slave Computer 18 File Transfer Utility After clicking on the Open File Transfer button from the toolbar, a window will popup as the picture is shown. The left side shows the directories from the Master Computer and the right side shows the directories from the Slave Computer. 19 There are 7 functions in the File Transfer Utility and they are listed as below: No. 1 2 3 4 5 6 7 Name Send Receive Delete New Folder Rename Minimize Close Description SendfilesfromMasterComputertoSlaveComputer ReceivefilesfromSlaveComputertoMasterComputer Deletetheselectedfile(s)orfolder(s) Create a new folder in the selected directory Renameafileorafolder Minimize the File Transfer Utility window Close the File Transfer Utility window 20 Send a file to Slave Computer Step 1 SelectthefilethatyouwishtotransfertotheSlave Computer in the Local Machine root table Step 2 Select the desire destination on the Slave Computer in the Remote Machine root table Final Step Click Send to begin the process. Receive a file from Slave Computer Step 1 Selectthefilethatyouwishtotransfertothe Master Computer in the Remote Machine root table Step 2 Select the desire destination on the Master Computer in the Local Machine root table Final Step Click Receive to begin the process. 21 Delete Files or Folders Selectthefilesorfoldersthatyouwishtodelete from either Master or Slave Computer, then click Deletetodeletethefile New Folder Select the desire destination for the new folder, then click New Folder to create the new folder Rename Selectthedesirefiletoberenamedandclick on Rename, then new window will popup with atextbar, simplyputthenewfilenameand extension and click Ok Minimize Simply click Minimize to minimize the File Transfer Utility window Close Simply click Close to close the File Transfer Utility window 22 Firmware Upgrade Step 1 Go to www. iogear. com to download the latest firmwarefortheunitfromthecomputerthatis beingusedforthefirmwareupgrade. Step 2 Extractthefilethatyouhavedownloadedby using software such as Winrar. Step 3 Connect either end of the USB port to computer thatisperformingthefirmwareupgrade. Step 4 Double-clicktheexecutionfilethatyouhave extractedtobeginthefirmwareupgrade process. Step 5 A window will popup, select the GCS661U CD drive no. then click start to proceed. Note: if you don't remember the drive no. , you can go to "My Computer" and check. 23 Step 6 Thenthenewfirmwarewillbegintoloadintothe GCS661U. Final Step Oncethefirmwareupgradehascompleted, a window will popup and say Upgrade Success, simplyclickOKtocompletethefirmwareupgrade process. 24 FCC Statement 15. 21 Youarecautionedthatchangesormodificationsnotexpresslyapprovedbythepartresponsiblefor compliance could void the user's authority to operate the equipment. 15. 105(b) his equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 25 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. this device may not cause interference and 2. [. . . ] All other brand and product names are trademarks or registered trademarks of their respective holders. IOGEAR makes no warranty of any kind with regards to the information presented in this document. All information furnished here is for informational purposes only and is subject to change without notice. assumes no responsibility for any inaccuracies or errors that may appear in this document. 30 31 About Us FUN IOGEAR offers connectivity solutions that are innovative, fun, and stylish, helping people enjoy daily life using our high technology products. [. . . ]