User manual IOGEAR GUH420 QUICK START

[. . . ] The IOGEAR Logo, a mark of quality 5. 4. System Requirements Minimum System Requirements: Mac · PowerMac G3 (Blue & White Tower) or later · Mac OS 9. 2 or higher -Mac OSX 10. 2 or higher is required for USB 2. 0 functionality · 64MB of RAM · Available USB port · Available 1394 FireWire port PC · Pentium® or K6® - class processor (266Mhz or higher) · Windows 98SE, 2000, ME, XP · 64MB of RAM · Available USB port · Available 1394 FireWire port Recommended System Requirements: Mac · PowerMac G4 1. 0Ghz or higher · Mac OSX 10. 2. 8 (Jaquar) or later · 256MB RAM · Available USB port · Available 1394 FireWire port PC · AMD Athlon® 2100+ or Intel Pentium® 4 2. 0Ghz Processor · Microsoft Windows 2000, or XP · 256MB RAM · Available USB port · Available 1394 FireWire port 6. Hardware Installation of USB 2. 0 Universal Hub Note: Before you begin, please make sure that your computer has been turned off. Step. 1 Connect the power adapter to the power supply and the other end to the USB 2. 0/Firewire Hub 2. [. . . ] 5 (If using the USB HUB) · Plug the Hi-Speed USB 2. 0 Cable (Type B connector) into the USB 2. 0 upstream port · Plug the Hi-Speed USB 2. 0 Cable (Type A connector) into your computer's USB 2. 0 or USB 1. 1 port. (If using the Firewire HUB) · Connect the 6 pin FireWire® cable that came with the COMBO hub to the FireWire® port on the back of the unit. · Connect the other end of the cable into your computer's FireWire® port or additional FireWire® hub. Turn on your computer Once your computer has finished booting up, a series of messages will let you know that the USB 2. 0 Hub has been recognized and the Hub is successfully installed. Note: If you are using non-high-speed USB 1. 1 port a series of warning will prompt to remind you that a nonhigh speed port has been detected. In that case just close the warnings windows and continue. Front: 7. Care & Handling To insure the maximum reliability of the USB 2. 0 / FireWire® Universal Hub please follow the guidelines listed below: · DO NOT open the case for it will VOID your WARRANTY. · Keep all cables out of isles and off desktops where they can be hooked and pulled. · Keep the card firmly secured in the shipping container when shipping the Hub. · Keep the environment around the card clean and free of excessive dust and chemicals. · Use a damp cloth to clean the Hub. NEVER put cleansers directly on the Hub. · DO NOT expose the Universal Hub to extreme temperatures. · DO NOT expose the Universal Hub to direct sun light for extended periods of time. · DO NOT get the Universal Hub wet. · DO NOT place the Universal Hub in an area with an excessive amount of dirt 9. Radio and TV Interference This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation 4-Port USB 2. 0 / 3-Port FireWire® Universal Combo Hub GUH420 Quick Start Guide 8. [. . . ] If so, what are the steps necessary to reproduce the problem?6) What version of the OS are you using?8) What have you already tried to resolve the problem?The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions, or updates. [. . . ]