User manual IOGEAR MINIVIEW GCS104U

[. . . ] System Requirements: Any PC or Macintosh computer with: An available USB port A USB-compliant operating system (Windows 95 OSR 2. 0, Windows 98, Windows 2000, MacOS 8. 1 or later) A standard HDB-15 video adapter Packing List Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Component Overview . . . . . . . . . . . . . . . . . . . . . Front View Back View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01 02 03 04 06 08 09 10 11 12 13 14 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] MiniviewTM switches support video resolutions up to 1920 x 1440. Buffering technology prevents system failure. Saves space, power, and equipment costs. Uses standard connectors to connect PC's. 3 Year Limited Warranty. Features 2 Specifications Port Se le ction LEDs Ho t K eys / Port Se le ction But ton Po rt-Se le cte d M onito r HDB -15 VGA (F) Type -A (D owns tre am) HDB -1 5 VGA (M ) Type -B (Ups tre am) M a x: 192 0 x 14 40, D D C2B 3 or 15 s e conds D C 5V 1 5mA Plas tic / M e ta l 5°C ~ 40°C - 20°C ~ 60°C 0 ~ 80 % RH, Nonc onde ns ing G- CS102U: 4 . 9 ounce s G-CS1 04U: 38 . 83 ounce s Co ns ole Conne c tors US B M onito r PC Conne c tors US B Vide o Re s olution A ut oScan Int e rv al Powe r Cons umpt ion Hous ing Ope rating Te mpe rature Storage Te mpe rature Humidity We ight D ime ns ions (L x W x H) G-CS10 2U: 4. 0" Specifications 3 Overview Front View: 1 Selected LEDs These LEDs indicate the currently selected port. 2 Auto Scan LED The Auto Scan LED flashes when Auto Scan Mode is in effect. 3 Port Selection Switch The Port Selection Switch is located on the front panel, just opposite the Select Arrow on the front panel. Press this push button to cycle among the connected computers. The Selected LED on the front panel lights to indicate which port is selected. On-Line LEDs These LEDs indicate that a computer is properly connected to the switch, powered on and operational. Auto Scan Switch This push button toggles Auto Scan Mode for the MiniViewTM: USB. Overview 4 Overview. . . Overview 1 4 5 2 3 5 Overview. . . Rear View 1. ) Console Video Connector Connect your monitor here. 2. ) Power Jack If you choose to use an external DC 5V power adapter, connect it here. 3. ) Scan Time Selection Switch This slide switch selects the amount of time the MiniViewTM: USB will monitor each port (3 or 15 seconds) when Auto Scan Mode is enabled. 4. ) Downstream USB Ports Connect your USB keyboard, USB mouse and two other USB devices here. 5. ) Upstream USB Ports These Upstream ports connect to your Mac or PC to provide the necessary connection between the MiniViewTM: USB and the computer. 6. ) PC Video Ports These video ports connect to your iMac, G3/G4 or PC to provide the necessary connection between the MiniViewTM: USB and the computer. Overview 6 Overview. . . Overview. . . 2 1 3 4 6 5 Overview 7 Installation Before you begin, make sure that power to your computers and peripherals (monitor, scanner, etc. ) is turned off. 1. ) Connect your monitor to the Console Video Port on the MiniViewTM: USB. 2. ) Connect your USB peripherals to the USB Downstream Ports on the MiniViewTM: USB. Make sure you have a USB keyboard and mouse at the very least. 3. ) If you choose to use an external 5V power adapter, plug the adapter into an AC source, then plug the adapter cable into the Power Jack on the MiniViewTM: USB. [. . . ] When you switch computers with the Port Selection Switch, it is the equivalent of disconnecting the device. Therefore, if you are experiencing problems when switching ports, please make sure you un-initialize the drivers for your USB devices before switching. Appendix A 12 11 Appendix B Contacting IOGEAR In the event that your MiniViewTM fails to function properly, or you wish to contact us for any other reason, here are a few ways to do so. IOGEAR 16560 Aston Street Irvine, CA 92606 Phone: (949) 250-1260 Toll Free: (888) 999-2836 Fax: (949) 250-1262 www. iogear. com info@iogear. com Appendix B 13 Appendix C Radio & TV Interference Statement This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]