User manual IOMEGA EUG

[. . . ] (SCSI command 04h) For additional help on software installation problems under Windows 95, Windows 3. 1, or DOS, refer to MANUAL. EXE on the Windows/DOS Install diskette. If you need further assistance, refer to the support information on the back cover of the Jaz Installation Guide. More Problem Solving Help User's Guide Warranty This product carries a one year limited warranty. For complete warranty information, refer to the detailed warranty statement shipped with this product. © 1997 Iomega Corporation. Iomega, the Iomega logo and Jaz are registered trademarks of, and the graphic swirl, hand and eye are trademarks of, Iomega Corporation. [. . . ] Additional blank disks for your Jaz drive are available preformatted for Macintosh or for Windows/DOS. SCSI Guidelines Emergency Disk Eject Hole Disk Eject Button* The Small Computer System Interface (SCSI) is an industry standard for connecting peripherals to most personal computers. SCSI rules define how to connect more than one SCSI device to the same SCSI connection (either built-in or from a SCSI host adapter). SCSI "Chain" * The disk eject button is disabled during normal operation on the Macintosh. If you remove the Jaz disk from the drive, store it in the protective case. · · To eject the disk on Windows/DOS systems, push the eject button. To eject the disk on Macintosh systems, drag the disk icon to the Trash icon. A SCSI chain is a series of SCSI devices cabled one to another on a single SCSI connection. You can add your Jaz drive to a SCSI chain. For any SCSI chain, the combined chain length (the total of all cables in the SCSI chain) should not exceed 6 meters (19. 6 feet). When you shut down your system, switch off power to the Jaz drive. Turn on the Jaz drive (and all other SCSI equipment) before or at the same time as you start your computer. SCSI ID SCSI ID is an address number (0 through 7) that is assigned to each SCSI device. In a SCSI chain, each device in the chain must have a different SCSI ID number, and ID 7 should NOT be used for any device as it is usually reserved for use by the controller. The Jaz drive is set at the factory to SCSI ID 4. If you need to change the SCSI ID on your Jaz drive, switch off power to the Jaz drive, use a pen or straightened paper clip to set the SCSI ID switch as desired, turn on power to the drive, and restart or reboot the computer. Power Connection SCSI Connectors (Fast SCSI-2) SCSI ID Switch PWR Handling Jaz Disks Always store Jaz disks in their protective cases when they are not inserted in the drive. Always remove the disk from the drive before moving the drive. WARNING Never open the disk door on a Jaz disk or drop a Jaz disk. Either could damage the disk and cause data loss. Drive Sleep The Jaz drive has an automatic sleep mode that spins down a Jaz disk after 30 minutes of inactivity. During drive sleep, the green power light remains on, and the disk automatically spins up again when accessed. You can use the Tools program included with your drive to change the drive sleep setting. Refer to the Jaz Tools Help file included in your Jaz software package for additional information. 4 SCSI ID 0 Term IAO I Termination Indicator Light SCSI Termination Switch (|=ON; A=Auto; 0=OFF) Power Switch Disk Eject in Case of Power Loss The Jaz drive must be powered on for normal disk removal. If you need to eject a disk during a power failure, turn off the Jaz drive power switch and push a straightened paper clip into the emergency disk eject hole on the front of the drive (see illustration above). CAUTION Never force a disk into or out of the Jaz drive. SCSI Termination SCSI rules require that the first and last devices in a SCSI chain (and no others) have termination ON in order to provide proper data transfer. On the Auto setting, the Jaz drive can set its own termination automatically as long as power to the drive is ON. The termination indicator on the back of the drive lights whenever the Jaz drive turns termination ON. Always turn off power to all devices in the SCSI chain before making any change to the SCSI configuration. If you encounter a special problem with termination on the Jaz drive, you can use a pen point or straightened paper clip to move the SCSI termination switch to manual ON ( | ) or OFF ( 0 ). [. . . ] When you run Guest, you can use your Jaz drive without having to permanently install the driver or Jaz Tools software. There are versions of Guest for Windows 95, Windows/DOS, and Macintosh. All versions of Guest can be conveniently loaded from a floppy diskette. For detailed instructions on using Guest, refer to "Help for Guest95" or GUESTHLP. TXT on the Install diskette for Windows/DOS, or to the Guest Help file installed on MacTM OS systems. 3 The Iomega software cannot find the Jaz drive, or the Jaz drive is not assigned a drive letter. (a) Turn on power to the Jaz drive before you boot or start the computer. [. . . ]