User manual IOMEGA IUG

[. . . ] Refer to the documentation that came with the adapter. The ultimate drive for today's power user . . . Getting the Most out of Your Jaz Drive drive · · · · · · · Your Jaz drive is a high capacity, high performance removable media drive which meets the latest Fast SCSI-2 specifications. With your Jaz drive you can: Store and run applications from a Jaz disk. Consolidate all your existing removable media. [. . . ] If you need to use a different SCSI ID for your Jaz drive, change the SCSI ID setting before installing the drive. (SCSI ID jumpers are located on the bottom of the drive. ) Optional SCSI ID jumper settings are illustrated below. If you remove the Jaz disk from the drive, store it in the protective case. After you push the eject button, the drive takes a few seconds to spin down and eject the disk. Handling Jaz Disks Always store Jaz disks in their protective cases when they are not inserted in the drive. Always remove the disk from the drive before moving the drive. WARNING Never open the disk door on a Jaz disk or drop a Jaz disk. Either could damage the disk and cause data loss. 2 A 2 A 1 A 1 A 0 A 0 A 0 The Jaz drive has an automatic sleep mode that spins down a Jaz disk after 30 minutes of inactivity. During drive sleep, the disk automatically spins up again when accessed. You can use the Tools program included with your drive to change the drive sleep setting. Refer to the Jaz Tools Help file included in your Jaz software package for additional information. SCSI ID Location 2 A 2 A A A 1 Drive Sleep A 2 SCSI ID 0 2 A 1 A 1 A 1 A 0 A 0 A 0 A SCSI ID 1 2 A 1 A 0 A SCSI ID 2 0 A 1 A 2 A SCSI ID 3 SCSI ID 4 (factory setting) SCSI ID 5 SCSI ID 6 SCSI ID 7 (reserved) Disk Eject in Case of Power Loss The computer must be powered on for normal disk removal from the Jaz drive. If you need to eject a disk during a power failure, turn off the computer power switch and push a straightened paper clip into the emergency disk eject hole on the front of the drive (see illustration above). CAUTION Never force a disk into or out of the Jaz drive. SCSI Termination SCSI rules require that the first and last devices in a SCSI chain (and no others) have termination ON in order to provide proper data transfer. SCSI termination for the internal Jaz drive is set by the termination block on the data cable ­ termination is ON when the data cable connector closest to the termination block is connected to the Jaz drive. If the Jaz drive is not the last device in the chain, you need to use a different data cable in order to be able to daisy-chain to the next device. NOTE: If external SCSI devices are connected to the same adapter as the Jaz drive, termination on the adapter must be removed. Refer to the documentation that came with the adapter for additional information. Non-Iomega SCSI Adapters Your Jaz drive is a high performance drive that will work with any SCSI adapter that has a compatible ASPI manager for Windows/DOS or 32-bit miniport driver for Windows 95. (If you are not sure that your adapter is 100% compatible, contact the dealer where you purchased the adapter or the adapter manufacturer. ) Before installing the Jaz drive, make sure the necessary software for the adapter is correctly installed on your system. To take advantage of all the features of your Jaz drive, either install Jaz Tools or always use the Guest program when operating the drive. Refer to MANUAL. EXE on the "Install" floppy for Windows/DOS for additional information on non-Iomega SCSI adapters. Troubleshooting If you encounter a problem while installing or using your Jaz drive, check this section for help. [. . . ] (c) Make sure that the stripe indicating pin one on the Jaz data cable matches up with pin one on your SCSI adapter or other SCSI connection. (d) Make sure that all cable connections are straight and fully seated. (e) If your Jaz drive is part of a SCSI chain, make sure each device in the chain has a different SCSI ID number (no duplicates). [. . . ]