User manual IROBOT VERRO 500

[. . . ] Retain the safety and operating instructions for future reference. Do not switch the pool cleaner ON if it is not fully immersed in water. Operating the cleaner out of water will cause severe damage immediately and will result in loss of warranty. Allow the cleaner to remain in the pool for 15 to 20 minutes following the end of its cleaning cycle. [. . . ] To stop Verro before the end of the cleaning cycle, press the red Power button on the Power Suppy. Light Off On LIGHT: Light indicates that robot is ON. OFF: Red button turns robot OFF. Floating Power Cord Socket www. irobot. com Using Verro (cont. . . ) When Verro has finished cleaning the pool it will stop automatically and the Power Supply light will go OFF. Wait 20 minutes before removing Verro from the pool to allow the motors to cool. Shut off and unplug the Power Supply every time you remove the cleaner from the water. Always remember to turn the Power Supply OFF and unplug it from the power outlet before removing the cleaner from the pool. 10 Unplug the Power Supply from the GFCI outlet. Never leave the Power Supply plugged in when Verro is not in use. 11 Unplug the floating power cord from the Power Supply (turn the locking collar on the plug counter-clockwise to unlock it). Rotate counter-clockwise and pull to unlock 1 Use the floating power cord to pull Verro to the edge of the pool, but use the handle to lift Verro out of the water. Water will drain from Verro as it is lifted. 10 iRobot Verro Owner's Manual How Verro Works Verro has a powerful motor that pumps 80 gallons of water per minute through the robot, generating suction at two vacuum intakes under the robot. The water passes through a filter bag that traps dirt and debris down to two microns in size. (For comparison, the period at the end of this sentence is more than 500 microns in size. ) The force of the water being pumped up through the bottom of the robot and out through the top helps Verro maintain traction on the pool bottom and walls. Brushes at the front and back of the robot loosen particles attached to the walls and bottom of your pool so that they can be vacuumed up, along with all of the other loose dirt and debris. Verro's coverage algorithm allows Verro to brush and clean your pool all the way from the bottom to the waterline in 3 hours. www. irobot. com 11 Cleaning the Filter Bag Verro uses the force of the water pumped through the filter bag to maintain traction on the pool floor bottom and walls. If the filter bag becomes clogged, Verro will not be able to clean as effectively and may have trouble moving along the bottom and up the walls properly. 1 Unplug the Power Supply. (Please keep the plug away from contact with water. ) Unplug the floating power cord (turn the locking collar counter-clockwise to unlock it) from the Power Supply. Place Verro upside down on a towel (to prevent scratching the robot's shell). Towel Unlock and remove the bottom panel by pushing the two locking tabs toward the sides of the robot. Locking Tabs Towel 1 iRobot Verro Owner's Manual Cleaning the Filter Bag (cont. . . ) Remove the filter bag assembly. Remove the filter bag from the support bars. Turn the filter bag inside out and rinse away any accumulated debris with a hose. Gently agitate and squeeze the bag while rinsing it until the water is clear. If this does not remove all visible dirt, machine wash the bag using cold water on the gentle cycle. Do not use detergents, fabric softeners, bleach or other additives. Turn the filter bag so that the felt surface is on the inside and the smooth, shiny surface is on the outside and place it back on the support bars. Label Replace filter bag assembly in the robot. Make sure the tabs click into place. www. irobot. com 1 Maintenance and Adjustment Rinsing Verro iRobot recommends that you rinse Verro with a garden hose after using it. This will extend the life of the plastic and keep your robot looking good for years to come. Storage Store Verro in a dry place out of direct sunlight at a temperature between 50 and 104 degrees Fahrenheit. The Power Supply is water resistant, but not waterproof and may be damaged by rain. Important: Failure to properly store Verro will result in loss of warranty. Changing the Brushes Eventually, Verro's brushes will need to be replaced. It is time to replace them when Verro is riding on its side tracks instead of on the brushes. Please read these instructions carefully before proceeding. [. . . ] Consider repositioning the Power Supply to keep the floating power cord away from objects on which it may get caught. 18) The pump impeller is fouled Verro gets The floating power cord is Use Detangler to untwist the cord. 17) stuck on its twisted floating power cord 0 iRobot Verro Owner's Manual iRobot Customer Care Please visit our web site at www. irobot. com for support tips, frequently asked questions or information about accessories and other iRobot products. Should you still need assistance, call our customer care representative at . . iRobot Customer Care Hours: · Monday ­ Friday 9AM ­ 7PM Eastern Time · Saturday 9AM ­ 6PM Eastern Time www. irobot. com 1 Register your iRobot®VerroTM today. [. . . ]