User manual IROX HBVR761

[. . . ] WEATHER STATION WITH CABLE FREE IN-OUT THERMOMETER UV MEASUREMET AND IN-OUT HYGROMETER MOONPHASE AND RADIO CONTROLLED CLOCK (SWISS SIGNAL "HBG") HBVR761 UV-X USER'S MANUAL 77 IROX TE761EL & TS32C/TS704 MANUAL (ENG) SIZE: W65 X H105 (mm) BY EMILY TSOI FILM 19/12/05 1. INTRODUCTION Congratulations on your purchase of the HBVR761. The basic package comes with a main unit, which is the weather forecast station and, 2 remote units, the thermo hygrometer sensor and the UV sensor. The main unit is capable of keeping track of the maximum and minimum temperature of different sites. [. . . ] The recorded atmospheric changes for the past 24 hour are displayed in a bar chart above the atmospheric pressure window. 4. UV-MEASUREMENT 3c) HOW TO CHECK THE BAROMETRIC PRESSURE 4a) Description The UV-Index (UVI) is an international standard defining the intensity of the UV radiation of the sun. The higher the UVI, the stronger is the UV radiation of the sun and therefore potentially harmful to humans. The UVI makes you aware of this and helps you to choose the correct protection. 4b) UV table and display indicates UV-Index Symbol Level Intensity weak Protection No protection necessary 0 -2. 9 3 - 5. 9 medium Protection necessary: Hat, t-shirt, sun glasses, sun cream The current and historical barometric pressure is shown on the atmospheric pressure window. For user staying at a higher altitude such as in the mountain area, see-level barometric pressure applies. Use [PRESSURE / ALTITUDE key to toggle the display to sea level pressure display. Press and hold the Pressure/Altitude key to enter the sea level pressure adjusting mode. Use the [ ] or [ ] (rear panel) key to enter sea level pressure and use [PRESSURE/ALTITUDE] to confirm. 88 6 - 7. 9 high Protection necessary: Hat, t-shirt, sun glasses, sun cream 8 - 10. 9 very high Additional protection necessary: Avoid to stay in unprotected areas 11+ extreme Additional protection necessary: Avoid to stay in unprotected areas 89 5. THERMOMETER / HUMIDITY 5a) HOW TO CHECK REMOTE AND INDOOR TEMPERATURES The wave display on the outdoors temperature indicates the reception of the remote unit is in good order. If no readings are received from the remote unit for more than two minutes, blanks " " will be displayed until further readings are successfully searched. Check the remote unit is sound and secure. You can wait for a little while or Hold [ ] for 2 seconds to enforce an immediate search. If the temperature or humidity goes above or below than the measuring range of the main unit or the remote unit (stated in specification), the display will show " " & "HHH" or "LLL" respectively. The unit can be set to automatically scan and display readings from the remote sensors, the display will show the readings from one channel for about 4-seconds and then proceed to the next channel display. -To activate the remote-sensor scanning mode: Press and the hold the button [CHANNEL] for 2 seconds. -To deactivate the remote-sensor scanning mode: Press and the hold the button [CHANNEL] for 2 seconds. 5b) HOW TO READ THE KINETIC WAVE DISPLAY The kinetic wave display shows the signal receiving status of the main unit. There are three possible forms: The unit is in searching mode. Temperature readings are securely registered. No signals. 5c) MAXIMUM AND MINIMUM TEMPERATURES AND HUMIDITY The maximum and minimum recorded indoor temperature, humidity and outdoor temperatures will be automatically stored in memory. To display them, Press [ MEM ] once to display the maximum readings and again the minimum readings. [. . . ] After 8 minutes, alarm sound will be wake up automatically. The snooze cycle will be restarted if you press the snooze key again. If you leave the alarm sound on for 2 minutes, it will enter snooze mode automatically with maximum 3 times. 8d) HOW TO STOP AN ALARM Press [ALARM] on the unit to stop an alarm. 95 8e) ALARM FEATURE * Weekday Alarm The alarm sound will be activated and the icon will be flashed on weekday when it is armed and the alarm time is reach. [. . . ]