User manual ITS TELECOM PANCAM-T ACCESS CONTROL DOOR PHONES SYSTEM

[. . . ] All of ITS's Access Control Door Phones incorporate cutting edge technology, providing a high quality speakerphone and a built-in electric lock control. All ITS's Access Control Door Phones are easy to set-up, modern and durable in design and provide "plug and play" installation. This guide provides installation and programming instructions for the following products: · PanCam unit · Pantel Outdoor unit · Pantel Indoor unit · Pancode Outdoor unit · Pancode Indoor unit 1. 1 PanCam The PanCam unit is available in two versions: PanCam-C (with keypad) and PanCam-T (one button). Both are wall mounted access control door phones, connected to an analog port of a PBX or a Key Telephone System, with an internal black & white or color high-quality pinhole camera encased within the unit. [. . . ] The following figure shows the terminal locations on the wire connector provided with the Pantel/Pancode. This connector is attached at the base of the internal component. All wiring to the Pantel/Pancode is attached to the wire connector. The Pantel/Pancode supports a bypass switch installation. This allows opening the door with a hardwired switch. A bypass switch should be connect to the SW and /SW terminals. Power Supply Normally Open/Closed Outputs Door Lock Relay Terminals Switch Terminals Phone Line/Extension ~12V ~12V N. C. DLR ~DLR /DLR SW /SW LINE LINE Figure 2-4. Connector Wiring Note: For the installation of the powered-unlocked-state, use DLR and ~DLR. For the installation of the poweredlocked-state, use /DLR and ~DLR (this is recommended for safety purposes). PanCam/Pantel/Pancode Installation and Programming Manual 11 Installation The wiring connector is a screw connector type. In order to attach a wire you must insert the stripped end of the wire into the proper terminal and tighten the terminal screw. For this installation, the access-control device bypass "Switch" wires are connected to the "N. O. " and "CMN" terminals of the Pantel/Pancode. The door-lock relay wires are connected to the access-control device (see Figure 2-6. ) Lock Relay Pancode/ Pantel N. O. Access Control - Controlling Lock Relay PanCam/Pantel/Pancode Installation and Programming Manual 13 Installation 2. 3 Connection Schematic The Pantel/Pancode offers multiple wiring options. · Option 1: For use with an external device, which requires the Pancode to be set up as "Normally Closed" · Option 2: For use with an external device, which requires the Pancode to be set up as "Normally Open" · Option 3: For use with the powered-unlocked-state lock relay (most common) · Option 4: For use with the powered-locked-state lock relay (recommended for safety purposes) The following schematic diagram shows the wiring plan for these four options. Figure 2-7. PanCam/Pantel/Pancode Wiring Schematics 2. 4 Volume Control The volume of the PanCam/Pantel/Pancode speaker can be adjusted using the volume controller located on the unit's back panel. After installing the unit, test the volume. In case it is too low/high, remove the unit from the mounting bracket and adjust the volume using a small screwdriver. 14 PanCam/Pantel/Pancode Installation and Programming Manual 3 Programming Programming can be done from any telephone or extension on the PBX, using keypad DTMF tones. The following programming functions are discussed in this section: · Day/Night Mode Selection · Entering Programming Mode · Resetting the PanCam/Pantel/Pancode 3. 1 Day/Night Mode Selection Day and Night mode specify which of the programmed destination numbers, Day or Night number, will be called when the Call button is pressed. The operator can manually change the Day/Night mode. To Change the Day/Night Mode 1. Dial the PanCam/Pantel/Pancode line/extension from any touch-tone telephone. Wait until the PanCam/Pantel/Pancode answers and beeps. Enter *80 for Day Mode -orenter *81 for Night Mode. 3. 2 Entering Programming Mode Note: You will hear a confirmation tone every time you enter a programming command. To Enter Programming Mode 1. [. . . ] *460 + X where: X = 1-9 (each step is 200 msec) *462 + XX XX = Seconds (10-99) 00 = Unlimited *464 + X XX = Number of seconds (1-9) *600 + (new password) Programming access passwords must be four numeric digits. The allowable characters are 0 through 9. Do not use the * or # keys. 8 0123 *For Outdoor units ONLY Time between DTMF's Conversation time limit (sec) Door opening time limit (sec) Changing the programming password 2 (400) 45 sec 3 sec 1234 22 PanCam/Pantel/Pancode Installation and Programming Manual Programming OPERATION COMMAND DEFAULT *For PanCam-C Camera instructions *620 + X X = 0 camera off X = 1 camera on X = 2 camera powered when call button is pressed X = 3 powered by any touch on unit keypad 0 3. 6 Entering Special DTMF Characters Special characters can be entered using the keypad. The following table shows the corresponding keypad entries needed for creating special DTMF characters. DTMF CHAR. [. . . ]