User manual JABSCO 29090-2000

[. . . ] Manual Toilets Model: 29120-2000 Manual Toilet, Regular Bowl Model: 29090-2000 Manual Toilet, Compact Bowl Applications You may install JABSCO Regular and Compact bowl manually operated marine toilets in both power and sailing craft, either above or below the waterline, for use on sea, river, lake or canal. Your installation may discharge the waste either overboard (provided that your national and local regulations allow this), or into a treatment system or into an on-board holding tank (U. S. C. G. Marine Sanitation Devices Type I, II and III). JABSCO manual toilets are designed specifically for marine use. Consult ITT Industries Jabsco for advice about possible non-marine applications. Features Design w Reversible pump mounting allows re-assembly for left hand operation by installer. [. . . ] w Offer up the toilet in the selected position and, using the holes in the base as a guide, mark the positions for the 4 bolt holes on the mounting surface. Remove the toilet and drill 4 vertical holes of 9mm diameter through the mounting surface. w Apply a bead of white silicone sealant to the outer rim of the bottom base. w Bolt down the toilet and tighten the fastenings securely. If you are not using self-locking nuts, use nut-locking compound. 2 w Remove the white hose supplied with the toilet, which connects the flushing pump outlet tail to the elbow (key 6). 3 Installation Instructions 5. 3 Outlet Pipework - 4 options Option 1: Toilet below the waterline and discharging overboard. (See Figure 1 on Page 3) YOU MUST fit a 38mm (1 /2") Vented Loop fitting, Jabsco part number 29015-0010. w If you fit a vented loop at the top of the hose loop this will ensure that you can keep some water in the base of the toilet without risk of it being siphoned away. 6. Testing Refer to the Operating Instructions and follow the procedure "2 Normal use". w If the flushing pump is hard to prime half fill the bowl with fresh water. Option 3: Toilet waste discharging into holding tank, top of holding tank above discharge elbow at anytime. (See Figure 3 below) YOU MUST fit a 38mm (1 /2") Vented loop fitting, Jabsco part number 29015-0010. w If there is ANY possibility that the discharge elbow may be below the top of the tank at ANY time, a ventilated anti-syphon loop must be fitted in the outlet pipework to ensure that the contents of the tank do not syphon out through the bowl. 1 7. Safety Ensure that this INSTRUCTION MANUAL reaches the owner, skipper or operator of the craft as it contains essential safety information. ON COMPLETION OF INSTALLATION: - SHUT THE FLUSH CONTROL ( - CLOSE BOTH SEACOCKS ) 2. Normal use Open inlet and outlet seacocks (and secondary valves if fitted). w Before use, ensure that there is enough water in the bowl to prevent the toilet paper becoming compacted at the bottom of the bowl. If the bowl is empty, move the Flush Control Lever (key 23) to the Open ( ) position and pump the handle (key 17) up and down until the flushing pump is primed and water enters the bowl. Then Shut ( ) the Flush Control. w Arrange the outlet hose to form a loop which is at least 20 cm (8") above the highest possible level that the tank may reach, and fit the Vented Loop at that highest point. Figure 3. w Operate the pump with long, smooth strokes for efficient and easy operation. w During use, pump as necessary to keep the contents of the bowl low enough for comfort. w Use good quality hard or soft household toilet paper, but do not use more than necessary. w After use, keep the Flush Control Shut ( ) and pump until the bowl is empty. w When the bowl is empty, Open ( ) the Flush Control again, and continue to pump until all waste has either left the boat, or reached the holding tank (allow 7 complete up/down strokes per metre (yard) length of discharge pipework). Then Shut ( ) the Flush Control and pump until the bowl is empty. Always leave the bowl empty to minimise odour and spillage. AFTER USE: - SHUT ( ) THE FLUSH CONTROL. [. . . ] w Flush the toilet in accordance with the OPERATING INSTRUCTIONS for NORMAL USE and, in particular, ensure that all waste has left the discharge pipework and that the bowl is empty. w CLOSE BOTH SEACOCKS (even if secondary valves are fitted) w If the vessel is being wintered afloat, WIRE SEACOCKS SHUT w Be ready to mop up any water that may come out of the system. Dimensions and Weights 2. Servicing - Seal replacement If water begins to leak around the piston rod (key 29) at the top of the pump, the seal assembly (key 18) is worn and must be replaced. YOU WILL need: s A Seal housing Assembly 29044-2000. w Unscrew the seal housing assembly (key 18) using a 24mm (15/16") spanner and remove the entire piston rod assembly from the toilet. [. . . ]