User manual JATON VIDEO-107PCI-3D

[. . . ] Video-107PCI-3D multimedia accelerator User Manual version 3. 00 Copyright © 1999 Jaton Corporation, USA. NOTICE The information in this document is subject to change in order to improve reliability, design, or function without prior notice and does not represent a commitment on the part of the company. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or the inability to use the product or documentation, even if advised of the possibility of such damages. No part of this manual may be reproduced or transmitted in any form or by any means without the prior written permission of the company. INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. [. . . ] In other cases, mode type and refresh rate adjustments may be necessary. Use the utility program, which provided by video card manufacturer or production developer. To centering the display with normal type (mode 3), and to reduce (decrease) the refresh rate with the monitor's specification. Q: What kind monitors can display 800x600 mode or higher resolution mode?Explain and Suggestion: To display 800x600 resolution at 60Hz refresh rate, the monitor must be capable of synchronizing a 31. 5KHz horizontal scan rate (e. g. , NEC 2A, 3D). At 72Hz refresh rate, the monitor must be capable of synchronizing a 48. 0KHz scan rate (e. g. , Sony HG 1304, NEC 4D, 5D, Seiko 1450). To display 1024x768-interlaced mode, the monitor must be capable of synchronizing a 35. 5KHz horizontal scan rate (e. g. , 20 NEC 3D, Seiko 1430 or 1440). To display 1024x768 non-interlaced mode at 60Hz, the monitor must be capable of synchronizing a 48. 7KHz scan rate (e. g. , Sony HG 1304, NEC 4D, 5D, Seiko 1450). To display 1024x768 non-interlaced mode at 70Hz, the monitor must be capable of synchronizing a 56. 4KHz scan rate (e. g. , NEC 4D). Q: Windows screen won't come up, it kicks back to DOS prompt. Explain and Suggestion: Windows 3. 1xTM, or Windows for workgroup 3. 1xTM The SYSTEM. INI file may contain different information with the system hardware, cause by the new integration or the new installation of a video adapter. The SYSTEM. INI file is located in the WINODWS\SYSTEM directory. Use MS DOS editor to open the file, and change the statement that is under [Boot description] Section: Display. drv= VGA Or, Under DOS prompt, type within Windows "SETUP", change the display selection to VGA then exit and restart Windows. Windows 95TM Inadvertently, certain configuration files (e. g. , msdos. sys, command. com) have been changed in the system. Proceed to correct that, is re-boot the system with a system (Windows'95) formatted floppy diskette. There are many reasons to causing the system booting-up with un-appropriated steps. Base on Microsoft support wizard on their WEBsite, there are many technical articles to help users with this subject, such as troubleshooting with VXD errors, virus, Fatal exceptions, etc. , more details cover on each issue are descriptive and familiar with, and exclusively further to our support. Q: System hangs-up after installing video driver. Explain and Suggestion: 21 then save changes, and restart Windows. Today, most video drivers are developed for 32-bit processing and may require a channel to Code/Decode. Conflict between device drivers and TSR (terminate-and-stay-resident) programs will inverted the display, and are particularly effectual at crashing computer. The most effective way to check for conflicts is to replace with the original video driver, or delete and re-install the current video driver to the system. Accomplishing IRQs (Interrupt Request Query) settings, or troubleshooting the conflicts on hardware source may necessary. Most PCI video cards designed for Plug-n-Play, that means video card IRQ's setup which controls by main board's (mother board) circuitry and BIOS. [. . . ] Including but not limited to the implied warranties of merchantability and fitness for a particular purpose. Manufacturer does not warrant against damages or defects arising out of improper or abnormal use of handling of the products; against defects or damages arising from 32 improper installation (where installation is by persons other than Manufacturer), against defects in products or components not manufactured or installed by Manufacturer, or against damages result from non-manufacturer made products or components. This warranty does not apply if the Product has been damaged by accident, abuse, or misuse. This warranty also does not apply to products upon which repairs have been effected or attempted by persons other than pursuant to written authorization by Manufacturer. 12. 2 Exclusive Obligation. This warranty is exclusive. [. . . ]