User manual JAWBONE JAWBONE

[. . . ] User's Guide Talk Button Earloop Noise Shield Button Earbud Voice Activity Sensor 1. Basic Stuff You Need to Know · Talk Button: Press once ­ Ans / End Press and hold 3 seconds ­ On / Off Press and hold 3 seconds for pairing (Jawbone must be off) Press and hold 3 seconds for Noise Shield On/Off Press once ­ volume up · Noise Shield Button: 2. Get Going Quickly · Activate phone's Bluetooth® feature, then press the `Noise Shield Button' for 3 seconds (Jawbone must be off) · On phone, `Search for New Devices' select "Jawbone"; passcode "0000" Jawbone®--Designed and manufactured by Aliph. Jawbone® and Aliph are trademarks of AliphCom. [. . . ] Just select "Jawbone" from the list of paired devices and connect to it. IMPORTANT: If the pairing cannot be completed within two minutes after the pairing mode has been activated, Jawbone's LED indicator will flash red and beep three times. Jawbone will then turn off automatically. Please repeat steps 2 to 8 above to pair Jawbone and the mobile phone again. `TALK BUTTON' once when Jawbone is in standby. Jawbone automatically enhances the volume of your call depending on the noise of your environment. If you want to adjust the volume of your call further, use your mobile phone's volume button or press the `NOISE SHIELD BUTTON' one time to increase the volume by one level (there are a total of six levels). 4. Turning Jawbone On and Off Press and hold the `TALK BUTTON' for three seconds until you hear a short beep. The LED status indicator will then flash white. IMPORTANT: After you turn Jawbone on, you may need to press the `TALK BUTTON' one time to reactivate pairing and resume the connection between the headset and the mobile phone. (For pairing instructions, please refer to the "Pairing Jawbone" section. ) Using Jawbone after it is Paired and Connected 1. To answer a call, press the `TALK BUTTON' once. To end a call, press the `TALK BUTTON' once. If Jawbone is connected to the phone and you make a call, the audio will automatically be routed to Jawbone. To make a call using voice dialing, press the 10 Turning off Jawbone To turn Jawbone off, press and hold the `TALK BUTTON' for three seconds until you hear a long beep. The LED status indicator will flash red and then go off. 11 Using Jawbone Talk Button Answering a Call When there is an incoming call, you will hear the ring through the earphone. Press the `TALK BUTTON' once to accept the call or answer the call using your mobile phone by following the phone's normal procedure. Ending a Call Press the `TALK BUTTON' once to end your call, or end the call using your mobile phone by following the phone's normal procedure. Noise Shield Button Turning Jawbone Noise Shield Off While on a call, press and hold the `NOISE SHIELD BUTTON' for 3 seconds. The LED status indicator will blink red and descending tones will be heard in the earpiece. Rejecting a Call If you do not wish to answer an incoming call, press the `NOISE SHIELD BUTTON' button once to reject the call. Dialing from Your Mobile Phone Simply make calls on your mobile phone by following the phone's normal procedure. Turning Jawbone Noise Shield On While on a call, press the `NOISE SHIELD BUTTON' for 3 seconds. The LED status indicator will blink white and ascending notes will be heard in the earpiece. Note: The Noise Shield technology is on by default whenever Jawbone is turned on or a call is received or placed. Voice Dialing from Jawbone If your mobile phone is equipped with a standard voice dialing function, simply press the `TALK BUTTON' once when in Standby Mode, and when you hear a beep say the voice tag. We recommend that you record the voice tag using Jawbone for maximum effectiveness. 13 12 Last Number Redialing from Jawbone Depending on your phone's functionality, you may be able to redial your last placed call by pressing the `TALK BUTTON' on your headset twice while in standby mode. Transferring a Call from Jawbone to Mobile Phone Handset While on a call, press and hold the `TALK BUTTON' for 3 seconds 2. Press the `NOISE SHIELD BUTTON' one time to increase the volume by one level. Jawbone has a total of six volume levels. By pressing the `NOISE SHIELD BUTTON' again, you will advance through these volume levels and hear a 2-step tone. Each successive volume level is identified by a corresponding pitch increase in the second tone. [. . . ] · Never allow children to play with the headset; the small components of the headset may be a choking hazard. · Observe all signs and displays that require an electrical device or RF radio product to be switched off in designated areas. · Turn off your Jawbone prior to boarding aircraft. Do not use inside an aircraft in flight unless allowed by your airline. [. . . ]