User manual JBL 902VX

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual JBL 902VX. We hope that this JBL 902VX user guide will be useful to you.

Lastmanuals help download the user guide JBL 902VX.


Mode d'emploi JBL 902VX
Download
Manual abstract: user guide JBL 902VX

Detailed instructions for use are in the User's Guide.

[. . . ] Every room is different and there are different tastes, so don't hesitate to experiment on your own. 40°-60° Fig. 1 PLACEMENT Bookshelf Models: For the best stereo reproduction, the two loudspeaker systems should be an equal distance from your listening position and separated so that the angle Tower Models: The Tower models cabinet height and driver placement allow for speaker placement directly on the floor. For the best stereo reproduction, the two loudspeaker systems should be an equal distance from your listening position and separated so that the angle between 2 J SERIES LOUDSPEAKERS them, at the listening position, is between 40 and 60 degrees. For example, if your listening position is 8 to 12 feet (2. 5m to 4m) from each speaker, the two systems should be about 8 feet (2. 5m) apart. [. . . ] Connections are made at the terminals located on the back of the J Series speakers. Preparing the Hookup Wire Carefully plan your wire lengths before cutting any speaker wire. Be sure to allow plenty of extra wire to help hide paths in corners, along baseboards, etc. 1. For Left and Right Speakers, first determine the wire length needed between the most distant speaker and the receiver or amplifier. Now make the hookup wires for both speakers this length, even if one loudspeaker is much closer to your amplifier than the other. This will help maintain proper signal balance. (For the J Center, determine the length needed from AV receiver's center channel output to speaker). Strip off 3/8" of insulation from both ends of each conductor. Twist each set of thin wires into a tightly-bunched spiral. At this point you need to identify a visual difference between the two conductors of each molded pair of speaker wire. Differentiating marks can be a different color wire (copper or "silver"); a strand of yarn in one conductor; thin, raised ribs on one Fig. 2 3 part of the outer insulation; or a printed "+" marking on one of the insulators. Wrong speaker switch, "A" or "B" speaker output. Sound source (CD, cassette deck, turntable) not turned on, not activated, not hooked up or not selected on amp/receiver front panel. POWER HANDLING Thanks to their high efficiency, the JBL J Series Loudspeakers will produce reasonable volume levels in a room of moderate size with very little amplifier power. However, using a small amplifier to obtain the desired volume listening levels may lead to overdriving the amplifier. This will generate high distortion levels and may cause damage to your loudspeaker. For the best performance, an amplifier should be selected with an output rating that is greater than the maximum power that will be used. This margin of reserve power will ensure that the amplifier will not attempt to deliver more power than its design allows. However, the amplifier's power rating per channel must not exceed the maximum recommended amplifier power for that specific loudspeaker model. Please see the specification section for details. Following these guidelines will provide virtually distortion-free sound reproduction and long loudspeaker life. No sound from one speaker 1. Balance control turned all the way left or right. 2. One of the connections between sound source and amp/receiver is faulty or has become disconnected. Both speakers play at low volumes but shut off as volume is increased OR sound turns on and off intermittently A few strands of speaker wire may be shorting out. [. . . ] AV receiver/amp "audio direct" switch is activated. This switch should be off to activate the 5 speaker surround mode. Sound source (VDP, VCR, CD, cassette deck, turntable) not turned on, not activated, not hooked up or not selected on AV receiver/amp front panel. The loudspeaker cabinet may be cleaned with a slightly damp cloth. To remove dust from the grille cloth, use a vacuum with a brush attachment. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE JBL 902VX

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual JBL 902VX will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag