User manual JBL AV2

[. . . ] JBL® PERFORMANCETM SERIES AV2 AUDIO/VIDEO PROCESSOR USER GUIDE IMPORTANT SAFETY INSTRUCTIONS 1. Install in accordance with manufacturer's instructions. Do not install near any sources such as radiators, heat registers, stoves or other apparatus that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] "ON" indicates that the condition exists, or is active; "OF" indicates that the condition does not exist, or is off. 5. 1-CHANNEL AND 7. 1-CHANNEL DIRECT INPUTS There are four listening modes available for use with surround sources such as DVD-Audio, SACD, HD-DVD or Blu-ray players. These listening modes are for use when the AV2 8-channel direct inputs are in use. We recommend you use these listening modes under the following conditions: · 5. 1 BYPASS ­ Use this listening mode when the Surround Back L/R inputs are NOT in use and the input source device has its own internal bass management system. The incoming audio stream passes from the source directly through to the volume control without any analog-to-digital conversion. This mode also mutes the unusued input jacks to prevent unwanted noise from interfering with system performance. 5-CHANNEL ­ Use this listening mode when the Surround Back L/R inputs are NOT in use and the input source device does NOT have its own internal bass management system. In this mode, the analog source is converted to digital so that it uses the same bass management options for the direct input as used for all other inputs. This mode also mutes the unusued input jacks to prevent unwanted noise from interfering with system performance. 7. 1 BYPASS ­ Use this listening mode when the 8-channel direct inputs are in use and the input source device has its own internal bass management system. The incoming audio stream passes from the source directly through to the volume control without any analog-to-digital conversion. 7-CHANNEL ­ Use this listening mode when the 8-channel direct inputs are in use and the input source device does NOT have its own internal bass management system. In this mode, the analog source is converted to digital so that it uses the same bass management options for the direct input as used for all other inputs. · · · · · 3-29 Setup SURROUND CONFIGURATION Harman Consumer Group, Inc. Selecting the SETUP menu, SURROUND CONFIG option opens the Surround Configuration menu, which is used to customize the list of available listening modes that can be applied to incoming signals. Each Mode Family has a subset of available listening modes that can be turned off. If the listening mode is set to OFF, then the applicable listening modes in that family are not available for selection from the mode buttons. If the listening mode is ON, then the applicable listening modes in that family are available for selection. These are not input-specific settings; if a Mode Family option is turned off, it is removed from the list of available listening modes for ALL inputs, and regardless of the incoming data stream. Some modes, such as Dolby Digital, DTS and the Stereo modes in the PCM menus, cannot be excluded from the mode selections. Note: The Logic 7 Default parameter is the one exception in the Surround Configuration menu ­ this parameter has different functionality, as described on the following page. MAIN MENU AUDIO CONTROLS VIDEO STATUS SETUP SETUP DISPLAY SETUP SPEAKER/EQ SETUP INPUT SETUP SURROUND CONFIG DOLBY CONFIG MUTE LEVELS POWER ON SETTINGS BASSQ*: NO *CHECK MANUAL FIRST SURROUND CONFIG LOGIC 7 DEFAULT: ON DOLBY MULTI-CHANNEL DOLBY 2. 0 DTS PCM 44. 1/48 kHz PCM 96kHz DOLBY MULTI-CHANNEL DOLBY 2. 0 DTS DTS 96/24: ON DTS NEO:6: ON DTS-ES MATRIX: ON DTS-ES DISCRETE: ON LOGIC 7: ON STEREO DOWN MIX: ON DOLBY PLII: ON DOLBY PLIIx: ON DOLBY VIRTUAL: OFF LOGIC 7: ON DOLBY VIRTUAL: OFF LOGIC 7: ON STEREO DOWN MIX: ON PCM 44. 1/48 kHz PCM 96kHz LOGIC 7: ON DOLBY PLII: ON DOLBY PLIIx: ON DTS NEO:6: ON 5/7 CH STEREO: ON LOGIC 7: ON DOLBY PLII: ON DOLBY PLIIx: ON DOLBY VIRTUAL: OFF DTS NEO:6: ON HALL: ON 5/7 CH STEREO: ON 3-30 JBL® PerformanceTM Series AV2 Audio/Video Processor Setup OFF, ON LOGIC 7 DEFAULT SETUP SURROUND CONFIG LOGIC 7 DEFAULT Allows the user to choose the Logic 7 mode as the default surround mode for all incoming audio signals. If this parameter is OFF, then the AV2 selects the native format of the incoming signal as the default listening mode. If set to ON, then all incoming audio signals are defaulted to the Logic 7 listening modes. Setting the Logic 7 Default to ON does not prevent other listening modes from being available through the Mode buttons. Selecting the DOLBY, DTS, DSP or STER soft button on the remote control switches the Mode menu selections to any listening modes available for those families. [. . . ] If a button is not pressed within three seconds, the RESET heading will revert to MAIN, indicating that the remote control is no longer in Reset mode. If this occurs, you will need to repeat this step to re-enter the Reset mode. After about 10 seconds, "RESET" is displayed in the Menu name section at the top of the LCD touchscreen. A new screen now displays with three options: ALL, PROG and EXIT. [. . . ]