User manual JBL BASS 1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual JBL BASS 1. We hope that this JBL BASS 1 user guide will be useful to you.

Lastmanuals help download the user guide JBL BASS 1.


Mode d'emploi JBL BASS 1
Download
Manual abstract: user guide JBL BASS 1

Detailed instructions for use are in the User's Guide.

[. . . ] · If BassPro's fuse must be replaced, be sure to use the same type of fuse and current rating as that of the original. CHOOSING A MOUNTING LOCATION FOR BASS 1: Choose a mounting location that doesn't interfere with cargo, the fold-down rear seat or the trunk lid. The best location is usually a corner of the trunk or cargo area, as shown in Figures 1 and 2. Securely mount BassPro to the mounting surface using the four enclosed self-tapping screws. [. . . ] IN-DASH MOUNTING Disassemble the Subwoofer Level Control by removing the two Phillipshead screws on the front panel, rear panel and on top. Remove the Subwoofer Level Control's bottom and side panels. Slide the Subwoofer Level Control's PC board forward to release the RJ11 connector from the back panel and remove the board along with the potentiometer, knob and connector as a single assembly. Choose a mounting location that allows easy access to the control, and provides 1-3/4" clearance behind the mounting surface. Drill a 9/32" hole in the mounting surface. Feed the Subwoofer Level Control's potentiometer shaft (with the knob removed) through the hole and use the nut and washer provided to hold the control in place (Figure 5). CONNECTING THE SUBWOOFER LEVEL CONTROL TO BASS 1 Route the cable behind the dash or other interior panels and under the carpet. Do not route the cable outside the vehicle. Connect the RJ11 cable between the RJ11 receptacle on the BassPro and the receptacle on the Subwoofer Level Control (Figure 6). BassPro Connection Panel Control Cable Socket for Control Cable Rear View of Level-Control Circuit Board LevelControl Circuit Board Figure 6. Subwoofer Level Control electrical connection. Washer Hex Nut Knob Figure 5. In-dash mounting of the Subwoofer Level Control. Figure 4. GAIN CONTROL: Use this control to adjust the relative volume (loudness) of BassPro with the other speakers in the vehicle. CROSSOVER: Use this control to adjust the amount of high-frequency information present in BassPro's output. A lower value signifies less highfrequency content. AUTO TURN-ON: For speakerlevel connections, used this switch to activate (or deactivate) BassPro's automatic turn-on circuit. For most speaker-level applications, slide the switch to the AUTO position. If you prefer to use the remote (REM) connection, slide the switch to the OFF position. REMOTE BASS CONTROL: Use this RJ-11 jack to connect the supplied remote bass control. Make sure the head unit is off and volume control is set to minimum. On BassPro's amplifier panel, set the Crossover to its maximum frequency of 120Hz, as shown in Figure 10. Note: If using the REMOTE BASS CONTROL, set GAIN to maximum and set the BASS CONTROL to the midpoint. Turn the head unit ON and play a selection of your favorite music track that has substantial bass. [. . . ] If you elect to not install the Remote Bass Control, adjust the GAIN control to the maximum level that provides undistorted output from the BassPro, with the head unit's volume control at its 3 o'clock setting. Note: In most cases the above steps will provide you with satisfactory results. However, the actual process may require several readjustments of each control, since the settings will interact with one another. If necessary, consult your authorized JBL car audio dealer for help in tuning your system. Figure 10. 6 TROUBLESHOOTING PROBLEM POWER LED not lit. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE JBL BASS 1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual JBL BASS 1 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag