User manual JBL CINEMAPROPACK600II

[. . . ] The product has been exposed to rain or water; or d. The product does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation; or e. The product has been dropped or damaged in any way; or f. [. . . ] However, press the same Input Selector dijl­o in Steps 1 and 3. · When a button is pressed on the remote, the red light under the Input Selector d h­jl­o for the product being operated should flash briefly. If the Device Control Selector flashes for some but not all buttons for a particular product, it does NOT indicate a problem with the remote but rather that no function is programmed for the button being pushed. Consult the Function List on 44 Remote Control Functions Channel Control Punch-Through The remote may be programmed to operate so that the channel control function for either the TV, cable or satellite receiver used in your system may be used in conjunction with one of the other devices controlled by the remote. For example, while using and controlling the VCR, you may wish to change channels on a cable box or satellite receiver without having to change the device selected by the DCR600II or the remote. To program the remote for Channel Control PunchThrough, follow these steps: 1. Press the Input Selector Button dij l­o for the device with which you wish to have the channel control associated and the Mute Button c at the same time until the red light appears under the Input Selector dijl­o and the Program Indicator LED lights. The Program Indicator LED will flash once. Press and release the Input Selector Button dijl­o for the device that will be used to change the channels. The Program Indicator LED will go out and the Input Selector dijl­o you pressed in Step 1 will blink three times and then go out to confirm the data entry. Example: To control the channels using your cable box or satellite receiver while the remote is set to control the VCR, first press the VID 1/VCR 1 Input Selector Button l and the Mute Button c at the same time. Next, release them and press the Volume Down Button w, followed by the VID 3/CATV/ SAT Input Selector Button n. Example: To use the VID2 button to operate a cable box, first press the VID2 Input Selector m and the Mute Button c at the same time until the red light glows under the VID2 Button m. Press the CBL/SAT Button n, followed by the three-digit code for the specific model you wish to control. Resetting the Remote Memory As you add components to your home theater system, occasionally you may wish to totally reprogram the remote control without the confusion of any commands, macros or "PunchThrough" programming that you may have done. To do this, it is possible to reset the remote to the original factory defaults and command codes by following these steps. Note, however, that once the remote is reset, all commands or codes that you have entered will be erased and will need to be reentered: 1. Press any of the Input Selector Buttons d h­jl­o and the "O" Button at the same time until the Program Indicator LED lights. Press the "3" Button three times. 3. The red LED under the Input Selector d h­jl­o will flash once for each press. The Program Indicator LED will flash three times and go out. When the Program Indicator LED goes out, the remote has been reset to the factory settings. 45 Configuring the DVD600II DVD Changer DVD Compatibility & Terminology The DVD600II is more than a DVD player; it will play the following disc formats: · Both 5-inch (12cm) and 3-inch (8cm) discs · CD audio discs · DTS audio discs · CD-R audio discs · CD-RW audio discs · DVD movie discs · VCD (video CD) discs · MP3 audio discs However, it will NOT play the following: · DVD discs with a Region Code other than the one for which the player is set · DVD discs with PAL format video · DVD-Audio discs · DVD-ROM data discs · DVD-RAM data discs · CD-R/RW data discs · CD-I discs · CD-G discs · SVCD discs · Photo CD discs Notes on DVD-Audio discs: · The DVD600II is not capable of playing selections in the DVD-Audio format. However, many DVD-Audio discs include audio tracks in the PCM, Dolby Digital or other formats which the DVD600II is capable of playing. [. . . ] If you use S-Video connections from the DVD600IIto the DCR600II, you must also use the S-Video input on your television. If you use the composite video connections from the DVD600II to the DCR600II, you must also use the composite video input on your television. · It is a normal artifact of DVD playback for pictures to jump or show some distortion during rapid play. · Due to the nature of this product category, DVD players, while being operated at elevated temperatures, may exhibit certain anomalies such as picture freeze-ups. [. . . ]