User manual JBL CVSAT50PAIR

[. . . ] The S36II and S36AWII loudspeakers may be positioned on the wall either horizontally or vertically. The grille logo on each speaker may be rotated depending on how the speaker is positioned. Gently pull the logo away from the grille slightly, rotate it to the desired position, and let go. When mounted vertically, the tweeter array may be positioned either up or down, depending on the height of the placement. [. . . ] If the speakers will be above ear level, the tweeter array should be positioned down, preferably no more than two feet above ear level. If the speakers will be mounted very low, it may be best to position the tweeter array upward so that it will be no more than two feet below ear level. The S36II and S36AWII enclosures are specially designed to angle the speakers toward the listener when mounted flush against the wall. When mounting the S36AWII speakers outdoors, we recommend that you place them under an overhang, such as roof eaves, for added protection, and that you use two of the supplied special angle-mount screws per speaker, which angle the speakers downward at a greaterthan-usual angle, facilitating water drainage. NOTE: When using the enclosed angle-mount screws, always use the top two screw locations appropriate for the specific mounting orientation of your S36AWII. Referring to the enclosed installation template, screw locations (1) and (2) are to be used when mounting the S36AWII horizontally so that these locations are on top. To mount the loudspeakers vertically, use locations (2) and (4) or locations (1) and (3), depending on the mounting orientation. Do not mount the S36AWII upside down (with screw locations (3) and (4) on Wall Roof eave Supplied Angle-Mount Screw (When using angle-mount screws, always utilize the top two screw holes on the S36AWII, depending on mounting orientation. ) Horizontal mounting: Use screwholes (1) and (2). Vertical mounting: Use screwholes (1) and (3), or (2) and (4), whichever are uppermost. Supplied Rubber Pad S36AWII top) because it won't be able to lock onto the screw heads. Remember that the JBL logo on the tweeter/mid faceplate can be rotated with choice of speaker position (vertical or horizontal). If the system plays at low volumes but shuts off as volume is increased: · Check all wires and connections between receiver/ amplifier and speakers. · Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. · If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/ amplifier. If there is no sound coming from one speaker: · Check the "Balance" control on your receiver/amplifier. · Check all wires and connections between receiver/amplifier and speakers. Make sure no wires are touching other wires or terminals and creating a short circuit. · Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. · In Dolby* Digital or DTS® mode, make sure that the receiver/ processor is configured so that the speaker in question is enabled. · Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. [. . . ] · Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem is in the same place, i. e. , the speaker that was working previously now has no sound and the speaker that was not working now sounds fine; or whether it has moved, i. e. , the speaker that was not working still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner's manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at www. jbl. com for further information. S P E C I F I C AT I O N S S36II/S36AWII Description: S36II ­ 3-Way 6" horizontal/vertical mirror-image wall-mount/ bookshelf loudspeakers S36AWII ­ 3-Way 6" horizontal/vertical mirror-image wall-mount/ bookshelf, weather-resistant loudspeakers Maximum Recommended Amplifier Power:** Nominal Impedance: Sensitivity (2. 83V/1m): Frequency Response (­3dB): Crossover Frequencies: High-Frequency Transducer: Midrange Transducer: 150W 8 Ohms 90dB 60Hz ­ 20kHz 650Hz, 3000Hz 1" Pure-titanium dome, with rubber surround, shielded; Elliptical Oblate SpheroidalTM (EOS) waveguide S36II ­ 4" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, shielded; Linear Field ProximityTM (LFP) bezel (model S36AWII uses a shielded WeatherPlasTM midrange) S36II ­ 6" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, SFGTM magnetic shorting rings, high-temp oversized Kapton® voice coil, , HeatScapeTM motor structure, cast-aluminum baskets, shielded (model S36AWII uses a shielded WeatherPlasTM woofer) Low diffraction, IsoPowerTM Sealed Straight-Line Signal PathTM (SSP) All-metal, gold-plated, 5-way binding posts 10-1/4" x 14-5/8" x 5" 260mm x 371mm x 127mm 11 lb/5kg We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility, that the loudspeakers described in this owner's manual are in compliance with technical standards: Low-Frequency Transducer: Baffles: Enclosure: Network: Terminals: Dimensions (H x W x D): Weight: * Dolby is a trademark of Dolby Laboratories. [. . . ]