User manual JBL EON 210P

[. . . ] PORTABLE PA 210P USER'S GUIDE For: Français, Deutsch, Español, visit www. jblpro. com 2 Contents Section 1: Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5 Section 2: Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Section 3: Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Section 4: The EON 210P PA System Power Amplifier . . . . . . . [. . . ] HEADPHONE OUTPUT This output allows the user to listen to the main output the EON 210P mixer. Headphones used will require a 3. 5 mm stereo plug. MASTER VOLUME and "PEAK LED LADDER" Your EON 210P is equipped with a "Master Volume" that controls the overall output volume of the system and a 5 light "Peak LED Ladder" that gives you a visual display of how much power you are using (think of the speedometer on your car). The red or top LED on the ladder indicates that you are approaching the maximum output by blinking or, when it stays on constantly, indicates you have reached the maximum output. As a frame of reference if a channel volume is on "7" and the "MASTER VOLUME" is on "7" you will have reached the maximum output before distortion is audible. 13 DIGITAL EFFECTS Your EON 210P is equipped with digital multi-effects designed to enhance instruments or vocals. There are four effects available on the EON 210P. An effect on a vocal or instrument can create a very natural sense of space for the listener and is great fun for the performer. Used correctly, effects enhance a voice or instrument in a very musical way but, when used to excess, they can make the music or voice less intelligible and unnatural. As a basic place to start turn the EFFECT control to "5" on the appropriate channel. Start with the EFX RETURN on "5" and then select an effect that is suitable for your application. If there is too much effect then turn down the EFX RETURN to suit your taste. Located on each mono input strip is a control labeled "EFFECT". This control determines the amount of effect for that specific channel. "EFX SELECT" determines what type of effect is selected. The "EFX RETURN" controls the amount of effect on a global basis. All channels that have the "EFFECT" control activated will be affected by turning this control up or down. 1. EFFECT BYPASS This turns all effects off 2. PLATE REVERB Use with Vocals and Acoustic Instruments 3. ROOM REVERB Use with Vocals, Acoustic and Electric Instruments, Percussion, Piano 4. SLAPBACK Short Echo with repeats for Lead Vocal, Karaoke, Rockabilly 5. HALL REVERB Use with Lead Vocal, Sustained Guitar 14 effe 2 Plate and 6. Turn the "MASTER VOLUME" to "0". Connect the microphone to the microphone cable and insert the male end into channel 1 of the EON 210P mixer. Depress the MIC/LINE switch ­ this increases the sensitivity of the input and is set for use with a dynamic microphone. Set the "TREBLE" and the "BASS" control to "0" (IN THE CENTER AT THE DETENT). Set the "REVERB" to "0". [. . . ] If the noise goes away, the problem is with the source or the connecting cable. Lower the channel volume on unused channels to "0" Speakers should be between the audience and the microphones in order to avoid feedback. Turn up the "monitor output volume" on the mixer Make sure that the channel input volume is turned up Your headphones have too high of an impedance. Try a different set of headphones. Feedback Microphones are too close to the speakers MONITOR OUTPUT is turned down Headphone signal is weak Channel Input is too low Impedance mismatch 21 Section 10: Contact Information Mailing Address: JBL Professional 8500 Balboa Blvd. [. . . ]