User manual JBL GT5-803

[. . . ] If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. [. . . ] The product exhibits a distinct change in performance ­ this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 1. All the safety and operating instructions should be read before the product is operated. The safety and operating instructions should be retained for future reference. All warnings on the product and in the operating instructions should be adhered to. All operating and use instructions should be followed. Unplug this product from the wall outlet before cleaning. If it is in Phantom or Stereo mode, the center speaker will not play. · Check the connections between the subwoofer and the center speaker. If you have low bass output, check the following: · Experiment with placement of the subwoofer. Remember, place the subwoofer in a corner to get maximum bass output from the system. · Increase the level of bass, using the remote control. Specifications ESC300 System Amplifier 200 watts total system output; front channels: 35 watts x 3 @ . 1% THD; surround channels: 15 watts x 2 @ . 1% THD; subwoofer: 65 watts x 1 @ 1% THD Signal-to-Noise Ratio 90dB Input Impedance 20k ohms Input Sensitivity 400mV Auto Turn-on Sensitivity 2mV/channel System Frequency Response (­6dB) 35Hz ­ 20kHz Subwoofer Dimensions (HxWxD) 15-1/8 x 13 x 14-1/2 inches 384 x 330 x 368mm Weight 34. 5 lbs/15. 7 kg Satellites (each) Dimensions (HxWxD) 4-3/8 x 3-3/16 x 3-3/4 inches 111 x 81 x 95mm Weight . 8 lbs/. 4 kg Occasional refinements may be made to existing products without notice, but will always meet or exceed original specifications unless otherwise stated. included "Smart" Powered subwoofer/controller. Five satellites for left, right, center and surrounds. Foot for horizontal placement of center speaker. Versatile remote sensor, and doublesided tape provided. MUTE VOLUME 0dB TEST CENTER ­ ­ L TREBLE Music + + R SURROUND SURROUND MODES Pro Logic BALANCE ­ BASS + + Simulated ­ 3 Stereo INPUT Video Stereo Aux TM JBL "error free" speaker cables. Extension cable XC300 available in 10-ft. length in either white or black. Remote control. features · Dolby* Pro Logic* Processor with additional Phantom, Simulated, 3-Stereo, and Stereo Surround modes. · Six channels of amplification for all speakers and subwoofer. · Five identical, 2-way micro-satellites with titanium tweeters. · Remote sensor with connection wire for easy placement. one. [. . . ] Press (­) to decrease the level of low-frequency information. 10­14. Surround Modes From the remote, press one of these buttons to directly choose the desired surround mode (see "Surround Modes" section). From the front panel, press (Surround Mode) to cycle between the surround modes. Input Selector From the remote, press either (Aux) or (Video) to select the desired input. [. . . ]