User manual JBL JBL ON TOUR PLUS Install Guide

[. . . ] For products intended to operate from battery power, or other sources, refer to the operating instructions. This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. [. . . ] Do not overload wall outlets, extension cords, or integral convenience receptacles, as this can result in a risk of fire or electric shock. Never push objects of any kind into this product through openings, as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. The power-supply cord or the plug has been damaged; or b. Objects have fallen onto, or liquid has been spilled into, the product; or c. The product has been exposed to rain or water; or d. The product does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation; or e. The product has been dropped, or the enclosure damaged; or f. The product does not appear to operate normally or exhibits a marked change in performance. of room volume, it is recommended that you use one HT PS300. Receiver/Processor Subwoofer Out THX Sub 1 Input Output THX Controls ( Bypassed ) Sub 2 Input Output Controls ( Bypassed ) Normal Mode: If your surround processor/ receiver does not contain a subwoofer crossover. Receiver/Amplifier Output Level On Crossover Frequency Stby 0 10 50Hz 120Hz Input Output THX Controls ( Bypassed ) Subwoofer Out L R THX 0° Phase Line Level Input Line 180° L R Note: Some receivers/ processors have a mono subwoofer output. In this case, you must use a "Y"connector (not included) in order to maximize the subwoofer's performance. High Level Inputs + High Level Outputs ­ ­ + + L ­ ­ R + High Level If your receiver does not have subwoofer outputs: Receiver/Amplifier Front Speakers Left Right + ­ ­ + Output Level On Crossover Frequency Stby 0 THX Controls ( Bypassed ) 10 50Hz 120Hz Input Output THX 0° Phase Line Level Input Line 180° L High Level Inputs R + High Level Outputs ­ ­ + + L Left Front Speaker ­ ­ R + Right Front Speaker + ­ + ­ Operation The HT PS300 contains a signal sensing auto turnon/off circuit. This feature will automatically turn the subwoofer on when you turn your system on and begin playing any program material. The subwoofer will return to standby when no signal is received for approximately 5 minutes. The power switch is for vacation use only. Standby LED Status Off Off On On LED Status Off On Off Mode Off On Standby Procedure Power switch off Power switch on and play program material Simply turn off your receiver/processor. The HT PS300 will turn off after approximately five minutes. The subwoofer will turn on when your receiver/processor begins playing again. Output Level Output Level 0 10 Note: When the THX/Normal switch is set to "THX, " the output control is bypassed. Output level is then adjusted at the THX processor. Output Level 0 10 Crossover Frequency The Crossover Frequency adjustment determines the highest frequency the HT PS300 will reproduce. It allows a seamless transition from the subwoofer to the satellite speakers. Experiment with this adjustment to find the crossover frequency that sounds best with your speakers. [. . . ] · If you are using the THX input, make sure the THX/ Normal switch is set to "THX. " · If you are not using the THX input, make sure the THX/ Normal switch is set to "Normal. " · If you are using the "High Level Inputs, " check all wires and connections between the receiver/amplifier and the subwoofer. Make sure all wires are connected and that none of the speaker wires are frayed, cut, or punctured. · Adjust the "Output Level" control. · Review proper operation of your receiver/amplifier. [. . . ]