User manual JBL L16 DECADE

[. . . ] 184 IMpOrTanT safETy InsTrUcTIOns PlEASE READ thE FOllOwINg PRECAutIONS bEFORE uSE: · · · · · · · · · · · · · · · · · · · Read these instructions, heed all warnings and keep for future reference. Do not block any ventilation openings; a minimum distance of 10mm around the entire apparatus is required for sufficient ventilation. No naked flame sources, such as lighted candles, should be placed on or near the apparatus. Attention should be drawn to the environmental aspects of battery disposal. [. . . ] Connect the external AM antenna for better reception. Unwind the FM antenna and straighten the wire for the best reception. Plug the power adapter into the "DC In" jack and then plug the adapter into a wall outlet. If an additional audio source is used, connect the source to the "Aux In" jack. FM ANT AM ANT AUX-IN DC 15V AAA AAA Aux In DC In FM ANT AM ANT AUX-IN DC 15V WWW. jbl. cOM 5 English AAA cOnTrOls 1. Press Menu/Up Level at any screen to display Top Menu (may require repeated presses, depending on which menu state the unit was previously in). Use Up/Down arrows to highlight 12-hour or 24-hour format. The clock is set! Note: During clock-setting, if there is no user input for 2 seconds, display will return to the Now Playing screen. Press any one of the Enter, Up/Down arrows, or Menu/Up Level to return to setting selection. Setting the Clock Base Unit Control Power Navigation Select Up Volume Down Volume Up Alarm Source Menu/Up Level Enter Preset Select Down 6 jbl On TIME 200p UsEr GUIdE 1. Press Source button to select the source (iPod/iPhone, AM, FM, Aux). Press "+" button to increase volume. Press "­" button to decrease volume. Playing Music Languages/Region 1. An icon will be displayed on the left when the alarm is enabled, and the alarm will sound at the set time. 5. Preset Select Up Menu/Up Level Enter Waking to the iPod/iPhone Use the steps under Alarm Setting and choose "iPod" as the source. On your iPod/iPhone, choose the song you would like to awaken to and press Play. Set the volume level on the JBL On TimeTM 200P unit. Put your iPod/iPhone to sleep by holding down the Play/Pause button (older iPod models may vary). The JBL On Time 200P system can be put to sleep by pressing the Power button. Select Down Note: If you choose the last song on your iPod/iPhone, please place the iPod/iPhone in repeat mode, which will ensure that the iPod/iPhone will continue playing past the last song. 8 jbl On TIME 200p UsEr GUIdE Screen Contrast/Brightness 1. 4. Press the Menu/Up Level button until you reach the Top Menu screen. Use Up/Down arrows to select Display and press Enter. Use Up/Down arrows to select Brightness or Contrast. Adjust settings using Up/Down arrows. Note: To set brightness to Auto, press the Down arrow until Auto is highlighted. Sleep Timer 1. 4. Press the Menu/Up Level button until you reach the Top Menu screen. [. . . ] Connect the Aux In cable to the headphone jack on your iPod/iPhone. Reposition your JBL On Time 200P unit until you find better reception. Note Is the display on?If not, power is not getting to your JBL On Time 200P; try the solutions shown. Incorrect source selection No sound or weak signal from the AM/FM radio Bad reception from current location If you are still getting a weak signal from AM broadcasts, connect the external AM antenna to the AM antenna jack. Interference Sound comes from one side/channel only Distortion (static, crackling or hissing sounds) iPod/iPhone or audio cable is not seated properly Noise may be caused by interference from a monitor, cell phone or other transmitting device JBL On Time 200P unit is being overdriven by an amplified audio source Volume level may be too high Check surrounding area for any possible interference; wrap up any excess cables. Make sure the iPod/iPhone or Aux In cable is seated all the way into the JBL On Time 200P unit. [. . . ]