User manual JBL ON STAGE

[. . . ] Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, or the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. To be completely disconnected from the power input, the main plug of the AC/DC adapter shall be disconnected from the main. [. . . ] This will prolong the life of your unit, help protect your device from static electricity and prevent potential damage. 4 jbl on STage 400id USer gUide fcc STaTemenT and warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Any special accessories needed for compliance must be specified in the instruction manual. compacT deSign The JBL On Stage 400ID loudspeaker dock is a complete 2. 1-channel audio system, in one easy-to-place footprint. digiTal power and dSp The system delivers sound with a powerfully tuned digital audio path. The clean and compact digital amplification, coupled with DSP (digital signal processing) equalization, efficiently provides the transducers with cool-running power. 6 jbl on STage 400id USer gUide Unpacking yoUr jbl on STageTM* 400id Carefully unpack your speaker system and identify all its components: JBL MENU JBL On StageTM* 400ID Adapters for iPod IR remote Power supply Audio cable QUick SeTUp inSTrUcTionS · · · · · Plug the barrel end of the power supply cord into the power jack and plug the other end into the wall. Next, push the power switch; a green LED will light up, indicating that the unit is powered. Find the correct adapter for your iPod, then firmly place it into the docking area shown. Next, place your iPod into the dock, making sure your iPod is firmly seated. Adjust the volume, using (+) to increase and (­) to decrease. Press both to mute the JBL On Stage 400ID unit. Press either button to unmute. Power Jack DC-In Power Switch Power USB Port USB Auxiliary Port Audio-In JBL Power DC-In USB Audio-In www. jbl. com 7 English SpecificaTionS JBL ON STAGETM* 400iD Frequency Response: 40Hz ­ 20kHz Power Consumption: 55 Watts maximum JBL On StageTM* 400ID Transducers: One AtlasTM (45mm) neodymium and four Odyssey® (25mm) Power: 1 x 30 Watts (woofer) 2 x 15 Watts (tweeters), at 1% THD Input Impedance: >10k Ohms Signal-to-Noise Ratio: >85dB Input Sensitivity: 250mV RMS for rated power output Power (USA/Canada): 120 Volts, 60Hz AC Power (Europe/UK): 220 ­ 240 Volts, 50Hz or 60Hz AC Power (Japan): 100 Volts, 50Hz or 60Hz AC Power (Australia): 240 Volts, 50Hz or 60Hz AC UL/CUL/CE-Approved Dimensions: 14-1/4" x 7-3/16" x 3-3/4" (W x D x H) (362mm x 183mm x 95mm) Weight: 3. 8 lb (1. 7kg) Power Supply Manufacturer: JBL, Inc. Power Supply Model: 700-0084 TroUbleSHooTing SOuND QuALiTY Symptom No sound from the JBL On Stage 400ID unit Possible Problem No power to the unit Solution Make sure the wall power outlet or power strip has power. Make sure all switches for the outlet/power strip are on and that all switches for the speaker system are on. [. . . ] Some devices will distort the output signal if the volume is set to Maximum. We recommend that the source device EQ be set to Flat or Off. Check input cable connection. Check the EQ setting on your iPod or source device JBL On Stage 400ID unit emits a loud hum or buzzing noise Speaker system experiences radio frequency interference or picks up a radio station Input cables are not plugged in properly Input cable may be picking up interference Wrap up excess input cable, in order to make it as short as possible. 8 jbl on STage 400id USer gUide TroUbleSHooTing chArGiNG AND SYNciNG Symptom iPod will not charge Possible Problem Wrong adapter is used The iPod is not making full contact with the docking station Solution Make sure correct adapter is used for your specific iPod model. Make sure the iPod is seated securely into the docking station. [. . . ]