User manual JBL ON TIMEAL ADAPTATOR INSTRUCTIONS

[. . . ] Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, or the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. [. . . ] The main plug of the AC/DC adapter should not be obstructed OR should be easily accessed during intended use. The marking information is located at the bottom of the apparatus. The battery shall not be exposed to excessive heat such as sunshine, fire or the like. The apparatus and AC/DC adapter shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the apparatus and AC/DC adapter. TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). THERE ARE NO USER-SERVICEABLE PARTS INSIDE THIS UNIT. PLEASE REFER SERVICING TO QUALIFIED HARMAN CONSUMER GROUP, INC. , SERVICE PERSONNEL. Never remove grille covers in order to service the speaker system. The speaker system does not contain any user-serviceable parts. imPORtANt NOtE FOR All ElECtRONiC PRODUCtS: Before inserting or unplugging audio cables from the source device's headphones or line-level output jacks, it is good practice to turn off the device first. Press both to mute the JBL On Stage 200ID system. 4 jbl ON StAGE 200iD USER GUiDE SPECiFiCAtiONS JBL ON STAGE 200iD Frequency Response: 40Hz ­ 20kHz Power Consumption: 20W maximum Power Input: 12V/1. 25A JBL On Stage 200ID Transducer: 1-3/8" (35mm) x 2 (full range per channel) Dimensions: 14-1/8" x 4-5/16" x 2-1/2" (W x D x H) (359mm x 110mm x 64mm) Weight: 1. 5 lb (0. 7kg) tROUblEShOOtiNG Symptom No sound from the JBL On Stage 200ID speaker system Possible Problem No power to the system Power adapter plug is not inserted correctly No volume or low volume Solution Ensure that the power supply is connected to a live power source and is properly connected to JBL On Stage 200ID. (Note: When the JBL On Stage 200ID system is powered, a green power LED should light up. ) Touch the volume "Up" (+) pad on the volume control to unmute and/or increase the system volume level. (Note: Touching the volume "Down" [­] pad lowers the system volume; touching both the [+] and [­] volume control pads at the same time will mute the system. ) Increase the volume level on the audio source device. Press the Play button on the iPod/iPhone or remote control. Check the connection of the wall adapter. Input source is low iPod/iPhone paused No power; green LED is not on Wall adapter is not plugged into the JBL On Stage 200ID system correctly Wall adapter is not receiving AC power Place the wall adapter in a known powered outlet; test the outlet with a lamp or other device. Connect the JBL On Stage 200ID system to a known audio source; test the audio source with headphones. www. jbl. COm 5 JBL is a trademark of Harman International Industries, Incorporated, registered in the United States and/or other countries. * The trademark On Stage is used with permission of OSA International, Inc. iPod and iTunes are trademarks of Apple Inc. , registered in the U. S. [. . . ] iPod and iTunes are trademarks of Apple Inc. , registered in the U. S. "Made for iPod" means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. "Works with iPhone" means that an electronic accessory has been designed to connect specifically to iPhone and has been certified by the developer to meet Apple performance standards. [. . . ]