User manual JBL ONST2UDP ADAPTATOR INSTRUCTIONS

[. . . ] Release the cap, and tug gently on the wire to make sure that the connection Gently pull the slack out of the wire and screw the shelf + stand onto the back ­ the of speaker in two places, as shown. is snug. Follow the same procedure to connect the negative wire to its terminal. Use the larger screw (Hardware Bag A) in the + upper screw hole, and the ­ smaller screw (Hardware Bag A) in the lower screw hole. + ­ ­ MOUNTING THE SATELLITES ON OPTIONAL FLOOR STANDS Important Safety Note: The supplied floor stand adapters facilitate installation with a variety of general-purpose floor stands available from many manufacturers. Since different stands will have different weight capacities and stability characteristics, it is the customer's responsibility to check with the stand manufacturer or dealer to determine whether that specific stand is capable of handling the weight and proportions of these loudspeakers in a safe and stable manner. [. . . ] Screw the floor stand adapter into the floor stand's threaded insert until the speaker is firmly attached to the stand. Back off slightly from the fully tightened position until the speaker is oriented as desired, then rotate the thumbwheel at the bottom of the floor stand adapter to secure the speaker to the stand. 3 WALL-MOUNTING 4 3 2 1 8 5 Important Safety Note: The customer is solely responsible for proper selection of mounting hardware not included with the speaker, and for proper assembly and installation of the wall bracket, including but not limited to the selection of appropriate weight-bearing supports and proper use of the bracket. JBL disclaims any liability for the selection of mounting hardware and/or bracket installation. Be sure to follow these bracket assembly and installation instructions carefully. If you have any questions or doubts about your ability to correctly wallmount the speakers, consult with your authorized JBL dealer or custom installer. Step 1: Unscrew and remove the large Molded Nut TM. If necessary, use the supplied Metal Bar as a lever by inserting it into one of the holes in the outer edge of the Molded Nut TM. Step 2: Firmly grasp the Ball and Shaft £ and pull it straight out of the Attachment Plate ¢. Avoid leaning it to the side for leverage, as this may break off a tab. 4 Step 3: Slide the Molded Nut TM onto the Ball and Shaft £ with the threaded opening facing the ball. Thread the Metal Nut ¡ all the way onto the Ball and Shaft £, between the Metal Nut ¡ and the back of the Satellite Speaker ¶, using large needle-nose pliers until it is firmly seated against the back of the Speaker ¶ and has locked the Ball and Shaft £ and the Speaker ¶ together. Note that once the Metal Nut ¡ is fully tightened, it may embed some marks on the back of the Satellite Speaker ¶. The wires supplied with the system may already be stripped and tinned for easy insertion into the speaker terminals. You may need to separate the two conductors further in order to thread them through the shelf stand or floor stand adapter. Speakers and electronics terminals have corresponding (+) and (­) terminals. Most manufacturers of speakers and electronics, including JBL, use red to and center speaker terminals, press the red or black plastic cap for the desired terminal, insert the bare end of the wire into the hole below the cap and release the cap. Gently tug on the wire to make sure that it is fully inserted. 5 SYSTEM CONNECTION Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. If you are using a subwoofer, follow the directions in that owner's guide to connect and configure it. Configure your receiver or processor to reflect the correct number of speakers in your system. If you have added one SCSSAT300/200 speaker to a 5. 1-channel system, reconfigure it as a 6. 1 system. If you have added two SCSSAT300/200 speakers to a 5. 1-channel system, reconfigure it as a 7. 1 system. Center ­ + The SCSSAT300/200 should be set to "Small. " If your receiver allows you to set the crossover frequency between the subwoofer and the speakers, select 100Hz or the setting that is the closest frequency below it. Left Front ­ + Right Front ­ + Subwoofer LFE In Receiver Left Front Subwoofer Out Right Front ­ + ­ + ­ + Center Left Surround Surround Back Left Surround Back Right Right Surround ­ + ­ + ­ + ­ + Left Surround ­ + Right Surround ­ + ­ + ­ + Surround Back Surround Back Left Right 6 TROUBLESHOOTING If there is no sound from any of the speakers: · Check that receiver/amplifier is on and a source is playing. · Check all wires and connections between receiver/ amplifier and speakers. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. · Review proper operation of your receiver/amplifier. [. . . ] If the system plays at low volumes but shuts off as volume is increased: · Check all wires and connections between receiver/ amplifier and speakers. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. · If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. If there is low (or no) bass output: · Make sure the connections to the left and right "Speaker Inputs" have the correct polarity (+ and ­). [. . . ]