User manual JBL P652

[. . . ] Remember to keep your sales receipt and this manual in a safe place so both are available for future reference. P452/552/652/953 OM 1/27/03 3:36 PM Page 2 INSTALLATION WARNINGS AND TIPS ABOUT THESE INSTRUCTIONS Installation of automotive stereo components can require extensive experience with a variety of mechanical and electrical procedures. Although these instructions explain how to install Power Series multielement speakers in a general sense, they do not show the exact installation methods for your particular vehicle. If you do not feel you have the experience, do not attempt the installation yourself, but instead ask your authorized JBL car audio dealer about professional installation options. [. . . ] · Turn off all audio components and other electrical devices before you start. Disconnect the (­) negative lead from your vehicle's battery. · Keep speakers in their package until final installation. When moving a speaker, always rest it with the cone or dome facing up. · Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface. · At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. · Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw. · For door installations, check the clearance with the windows throughout the range of the window's travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism. · If mounting speakers elsewhere, check for clearance around rear deck torsion bars, glove box or other structural elements. · Do not mount speakers where they will get wet. INSTALLATION Figure 1. Mounting the P452, P552, P652, P652s or P953 using the supplied grille. Rotate tweeter so it is angled toward the listener using the UniPivotTM (patent no. 6, 002, 780) feature on the P552, P652 and P8652. Figure 2. Modifying the P452 to be installed in locations requiring fewer than four mounting "ears. " NOTE: Grip the tab (preferably with pliers) and bend to detach it from the speaker. P452/552/652/953 OM 1/27/03 3:36 PM Page 3 INSTALLATION Figure 3. NOTE: The P6452 and P8652 speakers are designed to be installed under factory grilles. [. . . ] Select an appropriate adapter ring and secure it to the vehicle using the sheet-metal screws provided, then attach the speaker to the ring with the machine screws. Woofer terminals on bottom White Blue Red Black P452/552/652/953 OM 1/27/03 3:36 PM Page 4 SPECIFICATIONS Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: P452 4" two-way 4 ohms 50W RMS, 150W Peak 89dB 75Hz ­ 23kHz 2" (51mm) 3-1/2" (89mm) P552 5-1/4" two-way 4 ohms 55W RMS, 165W Peak 89dB 55Hz ­ 23kHz 2-3/16" (56mm) 4-11/16" (120mm) P652 6-1/2" two-way 4 ohms 75W RMS, 225W Peak 90dB 45Hz ­ 23kHz 2-1/4" (58mm) 5-1/16" (129mm) P652s 6-1/2" shallow-mount two-way 4 ohms 55W RMS, 165W Peak 90dB 55Hz ­ 23kHz 1-15/16" (50mm) 5-1/16" (129mm) P953 6" x 9" three-way 4 ohms 110W RMS, 330W Peak 90dB 35Hz ­ 23kHz 3-5/16" (85mm) 8-11/16" x 5-7/8" (221mm x 150mm) P6452 4" x 6" two-way 4 ohms 50W RMS, 150W Peak 89dB 75Hz ­ 23kHz 2-1/16" (53mm) 5-5/8" x 4" (143mm x 102mm) P8652 6" x 8" (and 5" x 7") two-way 4 ohms 75W RMS, 225W Peak 90dB 40Hz ­ 23kHz 2-7/16" (62mm) 7-3/16" x 4-15/16" (183mm x 126mm) GENERAL CARE The loudspeaker grilles may be cleaned with a damp cloth. Do not use any cleaners or solvents on the grilles or the speaker cones. A valid serial number is required for warranty coverage. [. . . ]