User manual JBL S-3

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual JBL S-3. We hope that this JBL S-3 user guide will be useful to you.

Lastmanuals help download the user guide JBL S-3.


Mode d'emploi JBL S-3
Download
Manual abstract: user guide JBL S-3

Detailed instructions for use are in the User's Guide.

[. . . ] However, a careful setup procedure will always be rewarding, and for best results we recommend placement well away from the boundaries of the room with preferably minimum 0. 75 m (30 in) distance to the wall behind the speakers, and 0. 75-1 m (30-40 in) distance to the side walls. A good guideline is to start by concentrating on the tonal balance of the sound, aiming for the most neutral reproduction. [. . . ] NOTE: New loudspeakers require a certain amount of "exercise" before they perform their best. A steady level of performance is achieved after 8-12 hours of operation, depending on the nature of the music and the level. Should you want to speed up this process you can use inter-station FM noise as a signal during periods, where you would normally not be listening to the speaker. Alternatively a CD player on "Repeat" would be an appropriate signal source. Wrap the remaining bundles around the binding post and twist the center stands. The knob can now be tightened securely, and any excess wire that is not in contact with the binding post surfaces should be trimmed to avoid short circuits. A very convenient way of connection is the use of 4 mm bananatype connectors, which are then, in turn, connected to the binding posts. Bear in mind, however, that the number of contact points should be kept to a minimum, and at the same time each contact should be as tight as possible. For the same reason, we recommend the use of the highest quality spade connectors, expertly connected to the selected cables. Spade lugs will together with the custom made binding posts made for the JBL TI speakers, make the best possible connection between the speaker wire and the loudspeaker system, minimizing any contact resistance that might degrade the sound ever so slightly. Any connection in an audio system should not be considered "good forever". Both left and right speaker wires should be the same length. In some systems, the amplifier may be located near the loudspeaker system and may be connected using a short length of speaker wire. Although a relatively long cable between the preamplifier and main amplifier is required by such a hook-up, the benefit of a short amplifier-to-loudspeaker connection will often outweigh the drawbacks. Connections to the loudspeaker system are made at the terminals located at the bottom of the enclosure. these terminals permit a variety of connection methods. The most straightforward connection is made by directly connecting clean bare wire. This way the connection is made by stripping 8-10 mm of insulation off the loudspeaker wire and passing the bare wire through the hole in the binding post. If the wire is too thick to pass through the hole in the terminal in one single bundle, separate the copper wire into three equal bundles, then pass the center bundle JBL Ti loudspeakers may also be connected to the power amplifier using several lengths of wire. the multi-wire connection method offers a number of options and advantages. Each section of the Ti-loudspeaker system's internal frequency dividing network is electrically separated and equipped with its own pair of input terminals This way each individual loudspeaker drive unit (and its associated network) can be connected independently to the power amplifier. The loudspeaker system is shipped from the factory with all the network sections interconnected by strapping bars, so that the loudspeaker can be hooked up to the amplifier by a single run of cables. [. . . ] CAUTION: Never connect two amplifiers to the same loudspeaker without first removing the strapping bars. Operating two amplifier channels with the bars in place can seriously damage the amplifiers and void the warranty. Another option is to power each separate drive unit (and its associated network section) from its own power amplifier. Up to four identical stereo power amplifiers may be used, although specialized amplifiers for low, mid and high frequencies can offer clear advantages. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE JBL S-3

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual JBL S-3 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag