User manual JBL SCS SAT500

[. . . ] DTS is a registered trademark of DTS, Inc. Laurent Rault Harman Consumer Group, Inc. Château du Loir, France 4/07 OWNER'S GUIDE PRODUCT LINE: PRO SOUND COMES HOMETM Harman Consumer Group, Inc. 250 Crossways Park Drive, Woodbury, NY 11797 8500 Balboa Boulevard, Northridge, CA 91329 516. 255. 4JBL (4525) (USA only) www. jbl. com © 2007 Harman International Industries, Incorporated. JBL is a trademark of Harman International Industries, Incorporated, registered in the United States and/or other countries. [. . . ] Screw the floor stand adapter into the floor stand's threaded insert until the speaker is firmly attached to the stand. Back off slightly from the fully tightened position until the speaker is oriented as desired, then rotate the thumbwheel at the bottom of the floor stand adapter to secure the speaker to the stand. 3 WALL-MOUNTING 4 3 2 1 8 5 Important Safety Note: The customer is solely responsible for proper selection of mounting hardware not included with the speaker, and for proper assembly and installation of the wallmount bracket, including but not limited to the selection of appropriate weight-bearing supports and proper use of the bracket. JBL disclaims any liability for the selection of mounting hardware and/or bracket installation. Be sure to follow these bracket assembly and installation instructions carefully. If you have any questions or doubts about your ability to correctly wallmount the speakers, consult your authorized JBL dealer or custom installer. Step 1: Unscrew and remove the large Molded Nut TM. If necessary, use the supplied Metal Bar as a lever by inserting it into one of the holes in the outer edge of the Molded Nut TM. Step 2: Firmly grasp the Ball and Shaft £ and pull it straight out of the Attachment Plate ¢. Avoid leaning it to the side for leverage, as this may break off a tab. 4 Step 3: Slide the Molded Nut TM onto the Ball and Shaft £ with the threaded opening facing the ball. Thread the Metal Nut ¡ all the way onto the Ball and Shaft £, and the back of the Satellite Speaker ¶, using large needle-nose pliers until it is firmly seated against the back of the Satellite Speaker ¶ and has locked the Ball and Shaft £ and the Satellite Speaker ¶ together. NOTE: Once the Metal Nut ¡ is fully tightened, it may embed some marks on the back of the Satellite Speaker ¶. However, these marks will be covered by the Metal Nut ¡. Step 6: Mount the Attachment Plate ¢ into a wood stud on the wall, using four 7 6 1 2 3 4 5 8 with the star washer side away from the ball. Refer to the exploded drawing for the proper orientation of these parts. Step 4: Screw the Ball and Shaft £ into the Threaded Insert § on the back of the Satellite Speaker ¶ until it is fully seated in the Threaded Insert §, but do not tighten, as you might dislodge the Threaded Insert §. Such damage would not be covered under the warranty. Step 5: Tighten the Metal Nut ¡ with the star washer side between the Metal Nut ¡ #10 panhead wood screws · at least one inch long (not supplied). Make sure that all four screws are driven into the stud and not into drywall. If the bracket needs to be mounted in drywall, the customer is responsible for selecting and using appropriate wall anchors and screws. IMPORTANT NOTE: The Metal Nut ¡ must be fully tightened against the Satellite Speaker ¶ as described in Step 5 before beginning Step 7, in order to avoid damage to the Threaded Insert §. Such damage would not be covered under the warranty. Step 7: Holding the Satellite Speaker ¶ with both hands, reinsert the ball portion of the Ball and Shaft £ into the Attachment Plate ¢. Step 8: Hand-tighten the Molded Nut TM while positioning the speaker for the desired orientation. If the Molded Nut TM is difficult to tighten by hand, insert the Metal Bar into one of the holes in the outer edge of the Molded Nut TM and use the bar as a lever. [. . . ] If your system has no subwoofer, consider adding a powered subwoofer. If there is no sound from the surround speakers: · Check all wires and connections between receiver/ amplifier and speakers. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. · Review proper operation of your receiver/amplifier and its surround sound features. [. . . ]