User manual JBL SCS200.5BK

[. . . ] Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. [. . . ] They should be placed at about the same height from the floor as the listeners' ears will be, or they may be angled toward the listeners. The center channel speaker should be placed directly above or below the television, and no more than two feet above or below the tweeters of the left and right speakers. It is often convenient to set the center speaker on top of the television set, as shown in the drawing. The surround speakers should be placed slightly behind the listening position and, ideally, should face each other and be at a level higher than the listeners' ears. If that is not possible, they may be placed on a wall behind the listening position, facing forward. Additional satellites may be purchased separately for use in 6. 1- or 7. 1-channel systems. MOUNTING OPTIONS SATELLITES AND SURROUNDS On shelves. 4 On the wall. Wall brackets are included. On optional stands. ATTACHING THE SHELF STAND TO THE SPEAKER Prepare the speaker wire as described on page 7. Thread the two conductors through the two holes in the stand bracket. Make sure to preserve the proper polarity (+ and ­ connections) by threading the positive conductor through the hole on the left, and the negative conductor through the hole on the right, looking at the front of the stand. Push down on the red speaker terminal and insert the bare end of the positive wire into the hole under the red cap. Release the cap, and tug gently on the wire to make sure that the connection is Gently pull the slack out of the wire and screw the shelf stand onto the back of the speaker in two places, as shown. snug. Avoid leaning it to the side for leverage, as this may break off a tab. 6 Step 3: Slide the Molded Nut TM onto the Ball and Shaft £ with the threaded opening facing the ball. Thread the Metal Nut ¡ all the way onto the Ball and Shaft £, with the star washer side away from the ball. Refer to the exploded drawing for the proper orientation of these parts. 7 1 Step 5: Tighten the Metal Nut ¡ with the star washer side between the Nut ¡ and the back of the Satellite Speaker ¶, using large needle-nose pliers, until it is firmly seated against the back of the Speaker ¶ and has locked the Ball and Shaft £ and the Speaker ¶ together. Note that once the Metal Nut ¡ is fully tightened, it may embed some marks on the back of the Satellite Speaker ¶. However, these marks will be covered by the Metal Nut ¡. Step 6: Mount the Attachment Plate ¢ into a wood stud on the wall, using four #10 panhead wood screws at least 6 2 3 4 5 8 Step 4: Screw the Ball and Shaft £ into the Threaded Insert § on the back of the Satellite Speaker ¶ until it is fully seated in the Threaded Insert §, but do not tighten, as you might dislodge the Threaded Insert §. Such damage would not be covered under the warranty. one-inch long (not supplied) ·. Make sure that all four screws are driven into the stud and not into drywall. If the bracket needs to be mounted in drywall, the customer is responsible for selecting and using appropriate wall anchors and screws. Important Note: The Metal Nut ¡ must be fully tightened against the Satellite Speaker ¶ as described in Step 5 before beginning Step 7, in order to avoid damage to the Threaded Insert §. Such damage would not be covered under the warranty. [. . . ] · Check all wires and connections between receiver/ amplifier and speakers. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. · In Dolby Digital or DTS modes, make sure that the receiver/processor is configured so that the speaker in question is enabled. · Turn off all electronics and switch the speaker in question with one of the other speakers that are working correctly. [. . . ]